Filter
Top Products
10
ADVANCED FuNCTIONS
MPEG Noise Reduction
: This setting is designed to address two specific
types of video distortion, mosquito noise and blocking artifacts. If you see
haziness or shimmering around the edges of objects or the scrolling credits
in a film, or if the image appears to “pixellate” into blocks, change the MPEG
Noise Reduction setting from Off to Low, Medium or High.
Cross Color Suppressor
: Turn this setting on to remove cross color
artifacts, which can occur when high-frequency luminance (brightness)
signals are misinterpreted as chroma (color) signals, causing unwanted
flickering, flashing colors or rainbow patterns. This setting is not available
with HDMI sources, or when no video signal is present.
Black Level
: This setting is only effective when used with the Composite
Video Output. Turn it on for a full black-level setting that provides the full
dynamic range of black as presented on most DVDs. When turned off, the
setting complies with standards for video with “setup”, and may be more
appropriate when your video display has limited video processing capability.
Deinterlacing
: For historical reasons, video information was interlaced.
That is, each refresh of the television screen displayed only half the pixels in
a frame, alternating between all of the even rows of pixels and all of the odd
rows. Modern displays are capable of displaying the complete frame all at
once by progressively scanning all of the rows of pixels from top to bottom.
For optimal viewing on a progressive-scan display (most flat-panel displays),
the video images must be deinterlaced. When viewing images via the
Composite Video Monitor Output, any time the AVR’s video output resolution
is 576i, this setting may be turned off.
Film Mode Detect
: This setting is only accessible when the Deinterlacing
setting is turned on. It compensates for the different frame rates in which
film and video are shot. Film is shot at a rate of 24 frames per second
(progressive scan), while video is shot at slightly less than 60 frames per
second (interlaced). The AVR is able to detect whether the program was
originally shot on film and transferred to video (e.g., to create a DVD), and to
compensate appropriately for any authoring errors in the conversion. Select a
setting of 3:2 (for NTSC materials), 2:2 (for PAL materials), Off or Auto.
How to Adjust the Custom Picture Settings
Set the Video Mode to Custom to display the picture settings, as shown in
Figure 37.
Figure 37 – Video Modes Custom Processing
With a color bar test pattern from a test disc or other source on screen, the
following adjustments may be made:
The color intensity setting on your TV. •
Color adjustments using the color bars, which may be (left to right) black, •
white, yellow, cyan (turquoise), green, magenta, red, blue, black.
The color transition, seen as sharp separation of the bars. •
The performance of the color circuits in your TV (with “Video” signals); bar •
edges should show no vertical crawling dots.
Use the gray scale and the black/white fields in the test pattern to adjust the
brightness and contrast.
Brightness Adjustment
Turn down the color control on your TV until the color bars appear in black 1.
and white.
Adjust the contrast to the lowest level where you still can see all gray scale 2.
bars separately and clearly.
Adjust the brightness so that the bars in the gray scale are all visible. The 3.
bar farthest to the left has to be as black as possible rather than gray but
the next gradation must clearly be distinct from it. The bars in the gray
scale should gradually and evenly change from black to white.
Contrast Adjustment
Adjust the contrast on your TV until you see a bright white bar in the lower 1.
right corner of the screen and a deep-dark-black bar to the left.
If the brightness of the white bar no longer increases when the contrast 2.
is turned up or the borders of white letters bloom (overlight) into the
black areas (drastically decreasing the sharpness of the type), the contrast
has been turned up too much. Reduce the contrast until these effects
disappear and the video still looks realistic.
If you are watching TV with ambient daylight, adjust the contrast so that 3.
a normal video picture looks the same as the surroundings in your room;
that way the eye is relaxed when watching the TV picture. Reduce the
setting when the surrounding light is dimmed to improve the sharpness
of the picture.
The gray scale in the middle line should retain the same distinction 4.
between each bar as before the contrast adjustment. If not, repeat both
Step 3 of the Brightness Adjustment and the Contrast Adjustment.
Color Adjustment
When the brightness and contrast are set optimally, adjust the color 1.
control. Set the level so that the colors look strong but still natural, not
overdone. If the color level is too high, depending on the TV, some of the
bars will seem wider or the color intensity will not increase when the
control is turned up. Test the color intensity with a video of pictures of
faces, flowers, fruit and vegetables.
Refer to a large white bar in your test pattern to tweak the warmth of the 2.
picture using the Tint control on your TV.
Sharpness Adjustment
Contrary to intuition, the picture will appear sharper and clearer with the
sharpness backed off from the maximum setting. Reduce the sharpness
setting on your television, and the setting on the AVR 460/AVR 360, if
necessary, to minimize the appearance of any white lines between the bars in
the gray scale portion of the test screen.