Filter
Top Products
fender.com
7
Front Panel
Your new Fender® amplifier comes equipped with the highest
quality tubes available, sourced from various manufacturers all
over the world. Because of occasional irregularities in supply,
the specific tube type used in each amplifier is subject to
change without notice.
When replacing output tubes, please note the specific tube
markings on the original tubes factory supplied with your
amplifier. For example, 6L6 output tube types used by Fender
include, but are not limited to: 6L6GC; 6L6WXT; 6L6C; 6L6GE;
etc. The installation of a different type may require significant
adjustment by a qualified technician to avoid reduction in
performance and tube life.
Additionally, Groove Tubes™ sorts and tests many of our
output tubes, and paints them with a color-coded label. If
your amp came supplied with, for example, White-labeled
6L6WXT tubes, then a new set of White 6L6WXT tubes will
be the perfect direct replacement.
If you have questions or concerns, contact your Fender dealer
or authorized service center.
Tube locations left to right at rear:
Vacuum Tubes
A. INPUT — Plug your guitar in here.
B. VOLUME — Adjusts the loudness of the Clean channel.
C. TREBLE / BASS — Adjusts the tone character of the Clean
channel.
D. DRIVE
*
— Selects the Drive channel, as indicated by the LED.
E. GAIN — Adjusts the distortion level of the Drive channel.
F. VOLUME — Use together with the Gain {E} knob to control the
loudness of the Drive channel.
G. TREBLE / MID / BASS — Adjusts the tone character of the
Drive channel.
H. REVERB
*
— Adjusts the level of the Reverb effect.
I. EFFECTS ADJUST — Press to adjust either Chorus or Delay
using the Time/Rate, Mix and Depth knobs.
NOTE: You must turn to activate the Time/Rate, Mix and
Depth knobs after you switch between effects, otherwise the
knob positions will not show the actual settings for the newly
selected effect.
J. TIME/RATE —
Delay: Adjusts the interval between delayed repeats.
Chorus: Adjusts the speed of the chorus sweep.
K. DELAY
*
— Press to activate the Delay effect, as indicated by
the LED.
L. MIX — Adjusts the level of the Delay and Chorus effects. The
Chorus effect in the VM amplifier will deliver a chorus effect
with Mix set near the center of its range, or a true pitch-
shifting vibrato effect with Mix set to "."
M. CHORUS
*
— Press to activate the Chorus/Vibrato effect, as
indicated by the LED.
N. DEPTH —
Delay: Adjusts the number of delayed repeats.
Chorus: Adjusts the intensity of the chorus/vibrato effect.
O. POWER JEWEL — Indicates the amplifier is on.
INPUT POWER
120V 60Hz
180W
ATTENTION:
UTILISER UN FUSIBLE DE RECHANGE
DE MEME TYPE ET CALIBRE
CAUTION:
TO REDUCE THE RISK OF FIRE, REPLACE
FUSE WITH SAME TYPE AND RATING
WARNING:
FENDER A MPLIFIER SYSTEMS A RE CAPABLE OF P RODUCING
VERY HIGH SOUND PRESSURE LEVELS WHICH M AY CAUSE
TEMPORARY OR PERMANENT HEARING DAMAGE. USE CARE
WHEN SETTING AND ADJUSTING VOLUME LEVELS DURING USE.
TYPE: PR 773
SERIAL NUMBER
F3A L
250V
FUSE
POWER
ON
STANDBY
ON
MAIN
(8MIN)
EXTERNAL
(8MIN)
CAUTION: CHASSIS SURFACE HOT
WARNING: TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE
AVIS: RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
ATTENTION: SUPERFICIE DE
CHASSIS CHAUDE
FENDER MUSICAL INSTRUMENTS CORP.
CORONA, CA U.S.A.
MADE IN MEXICO
MODEL
40W
4 min TOTAL
SEE MANUAL
WARNING:
MAINTAIN 6" CLEARANCE
FOR VENTILATION.
EFFECTS LOOP
SEND RETURN
FOOT
SWITCH
*
Footswitchable: You can activate this control remotely from the included 4-button footswitch!