Fender Hot Rod DeVille ML Stereo Amplifier User Manual


 
DEUTSCH
DEUTSCH
ITALIANO
ITALIANO
FRAN
çAIS
FRAN
çAIS
ESPAÑOL
ESPAÑOL
ENGLISH
ENGLISHENGLISH
T. POWER CORD - Connect the power cord in
accordance with the voltage and frequency ratings
listed on the rear panel of the unit.
U. FUSE - The fuse protects the unit from electrical
faults. Replacement fuses must match the type and
rating specified on the fuse holder. If the unit
repeatedly blows fuses, have the unit tested at an
authorized Fender
®
Service Center.
V. MAIN SPEAKER - One of the following speaker load
configurations (internal or external) must always be
connected as shown below, when the unit is on:
DeVille 410 DeVille 212
*Insert an open plug (no speakers connected) for this
configuration.
W. EXTERNAL SPEAKER - This jack is wired in parallel
with the main speaker jack and must only be used
with something connected to the main speaker jack
as shown in the MAIN SPEAKER {V} description
above.
X. FENDER
®
/GROOVE TUBES™ GT6L6B - The
output tubes in your new Hot Rod™
amplifier are performance matched and
labeled as a color-coded pair. When
replacing these tubes, we recommend
selecting new tubes that have the same red, white or
blue color labels as the originals. Otherwise, tube
bias may need adjustment. See Specifications
below for your color coded part number.
Y. PREAMP TUBE STABILIZER -
A vibration–absorbing stabilizer is
installed around the preamp tubes to
minimize tube microphonics that
normally develop over time. The stabilizer can be
used with all preamp tubes compatible with your
Hot Rod™ amplifier.
1.
2.
3.
1.
2.
3.
2
**
V. W. V. W.
HOT ROD DEVILLE 410 HOT ROD DEVILLE 212
TYPE: PR 247 PR 247
PART NUMBERS: 021-3201-000 (120V, 60Hz) USA 021-3200-000 (120V, 60Hz) USA
021-3231-000 (240V, 50Hz) AUS 021-3230-000 (240V, 50Hz) AUS
021-3241-000 (230V, 50Hz) UK 021-3240-000 (230V, 50Hz) UK
021-3261-000 (230V, 50Hz) EUR 021-3260-000 (230V, 50Hz) EUR
021-3271-000 (100V, 50/60Hz) JPN 021-3270-000 (100V, 50/60Hz) JPN
POWER REQUIREMENT: 180W 180W
POWER OUTPUT: 60W into 8or 4at 5% THD 60W into 4or 2at 5% THD
INPUT 1/2 IMPEDANCES: 1 M/ 136 k 1 M/ 136 k
PRE-AMP OUTPUT IMPEDANCE: 1.5 kMax 1.5 kMax
POWER-AMP INPUT SENSITIVITY: 200 mV for clipping 200 mV for clipping
POWER-AMP INPUT IMPEDANCE: 54 k 54 k
TUBES: Three Fender Groove Tube GT12AX7 (099-4005-000) Three Fender Groove Tubes 12AX7A (099-4005-000)
*(Tube label color: Red=1, White=2, Blue=3) Two Fender Groove Tube GT6L6B (099-4401-*02) Two Fender Groove Tubes GT6L6B (099-4401-*02)
FUSE: 3A250V fuse (100V and 120V versions) 3A 250V fuse (100V and 120V versions)
1.6A 250V fuse (230V and 240V versions) 1.6A 250V fuse (230V and 240V versions)
SPEAKER: Four 10” 8Fender Model V 1030 Two 12” 8Fender Re-issue
Special Design (048832) Gold Label (037617)
FOOTSWITCH: 2 Button: Gain, Channel (050419) 2 Button: Gain, Channel (050419)
DIMENSIONS HEIGHT: 23.5 in (59.7 cm) 21 in (53.3 cm)
WIDTH: 23.5 in (59.7 cm) 24.25 in (61.6 cm)
DEPTH: 10.75 in (26.7 cm) 10.75 in (27.3 cm)
WEIGHT: 50 lb (22.5 kg) 53.5 lb (24.2 kg)
Product specifications are subject to change without notice.
Fender
Fender
®
®
Hot Rod™ DeV
Hot Rod™ DeV
ille/DeV
ille/DeV
ille 212
ille 212
7
Specifications
Specifications
wwwwww
..
ffeennddeerr..ccoomm
wwwwww
..mmrrggeeaarrhheeaadd..nneett