Filter
Top Products
MTP R 15HD RSA D • Reference Information
Reference Information
MTP R 15HD RSA D • Reference Information
A-2
A-3
Specs file:
incorporated and E1's recom-
mendation of cable type.
Specifications
Video
Gain ................................................. Unity
Number/signal type ..................... 1 set of proprietary analog signals
Connectors ..................................... 1 female RJ-45 on a pigtail
Video input — See MTP Series Transmitters' video
output specifications.
Video output
Number/signal type ..................... 1 analog VGA-UXGA RGBHV, RGBS,
RGsB, RsGsBs, HD component video,
component video, S-video, or composite
video
Connectors
..................................... 1 female 15-pin HD
Nominal level ................................ 1 Vp-p for Y of component video and
S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of
component video
0.3 Vp-p for C of S-video
Minimum/maximum levels
........ 0.3 V to 1.45 Vp-p
Impedance ...................................... 75 ohms
Return loss ...................................... <-30 dB @ 5 MHz
DC offset ......................................... <±20 mV with input at 0 offset
Sync
Output type .................................... RGBHV, RGBS, RGsB, RsGsBs
Standards ........................................ NTSC 3.58, NTSC 4.43, PAL, SECAM
Output level ................................... 4.0 V to 5.0 Vp-p, unterminated
Output impedance ........................ 110 ohms
Polarity............................................ Positive or negative (switch selectable)
Audio
Number/signal type ..................... 1 set of proprietary analog signals from an
MTP transmitter
Connector
....................................... 1 female RJ-45
Gain ................................................. Unbalanced output: 0 dB;
balanced output: +6 dB
Frequency response
...................... 20 Hz to 20 kHz, ±1 dB
THD + Noise .................................. 0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal
level
S/N
.................................................. >70 dB at maximum output (unweighted)
CMRR .............................................. >43 dB @ 20 Hz to 20 kHz
Audio output
Number/signal type ..................... 1 mono, balanced/unbalanced
Connector ....................................... (1) 3.5 mm captive screw connector, 5 pole
(uses 3 poles)
Impedance
...................................... 50 ohms balanced, 100 ohms balanced
Gain error ....................................... ±1 dB channel to channel
Nominal level ................................ +4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level .............................. >+14 dBu, unbalanced at 1% THD+N
Control/remote — external device (pass-through,
unidirectional or bidirectional)
Serial control port input/output . 1 set of proprietary signals on a female
RJ-45 jack
Serial control port output/input
. RS-232 via 3 poles of a 3.5 mm captive
screw connector, 5 pole
N
The serial communications link is unidirectional only, transmitter
to receiver, unless the receiver's directional DIP switch has been
repositioned. The switch should be repositioned only when the receiver
is the only one in the system.
Baud rates
....................................... Up to 38400 bps at up to 1000' (300 m)
(Higher data rates and distances are
possible. Performance varies based on
baud rate and cable length.)
Protocol
........................................... Data bits = 5 through 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
N
Protocol is mirrored between the transmitter and the receiver.
Serial control pin congurations . Captive screw connector: 1 = TX, 2 = RX,
3 = GND
General
Recommended cable type ............ CAT 5/5E/6 (shielded or unshielded)
External power supply ................. 100 VAC to 240 VAC, 50/60 Hz, external;
to 12 VDC, 2 A, regulated
Power input requirements
........... 12 VDC, 0.5 A