Filter
Top Products
9
ENGLISH FRANÇAIS ESPAÑOL PORTUGUÊS ESPAÑOL NEDERLANDS SVENSKA
9
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA
3
Use ui to select “SW Mode”, and
use o p to select a detailed setting.
Enter ReturnENTER BACK
LPF for LFE
SW Mode
100Hz
LFE+Main
1
Bass
SW Mode
Select low range signals to be
reproduced by subwoofer.
•LFE : The low range signal of the channel set to
“Small” speaker size is added to the LFE signal
output from the subwoofer.
•LFE+Main : The low range signal of all channels
is added to the LFE signal output from the
subwoofer. This is usually the best setting for
most systems.
•“SW Mode” can be set when “Speaker Config.”
– “Subwoofer” (vpage 6) is set to other
than “No”.
•Play music or a movie source and select the
mode offering the strongest bass.
•Select “LFE+Main” if you want the bass signals
to always be produced from the subwoofer.
NOTE
If “Front” and “Center” for “Speaker Config.”
are set to “Large”, and “SW Mode” is set to
“LPF for LFE”, no sound may be output from
the subwoofers, depending on the input signal or
selected surround mode.
4
Press ENTER to enter the setting.
Speaker Config.
Distances
Levels
Crossovers
Bass
LPF for LFE
SW Mode
Speakers
Enter ReturnENTER
BACK
1
Use ui to select “Bass”, and then
press ENTER.
Speaker Config.
Distances
Levels
Crossovers
Bass
LPF for LFE
SW Mode
Speakers
Enter ReturnENTER
BACK
Enter ReturnENTER BACK
LPF for LFE
SW Mode
100Hz
LFE+Main
1
Bass
2
Use o p to select the frequency.
LPF for LFE
Set LFE signal playback range. Set
this when you want to change the
playback frequency (low pass filter
point) of the subwoofer.
•80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz /
200Hz / 250Hz
Crossovers (Continue)
2
Use ui to select a speaker, and use
o p to select the frequency.
Front / Center / Surround
Select speaker for setting of crossover
frequency.
•40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz /
120Hz / 150Hz / 200Hz / 250Hz : Set the
crossover frequency.
•“Crossovers” can be set when the “Bass”
– “SW Mode” (vpage 9) setting is
“LFE+Main”, or when you have a speaker that
is set to “Small”.
•The default crossover frequency is “80Hz”,
which will work best with the widest variety
of speakers. When using very small speakers,
however, you can choose a higher setting
based on the specified frequency response of
the speakers. If the speaker has a specified
frequency response of 120 Hz – 20 kHz (as an
example), then choose the 120 Hz crossover
frequency.
•For speakers set to “Small”, low frequency
content below the crossover frequency is
attenuated to the speakers and the low bass
content is then re-delivered to the subwoofer(s),
or the front (L/R) speakers if they have been set
to Large.
•The “SW Mode” setting (vpage 9)
determines which speakers can be set.
• When “LPF for LFE” is selected, speakers set
to “Small” at “Speaker Config.” can be set. If
the speakers are set to “Large”, “Full Band”
is displayed and the setting cannot be made.
• If set to “LFE+Main”, this setting can be made
regardless of the speaker size.
3
Press ENTER to enter the setting.
Speaker Config.
Distances
Levels
Crossovers
Bass
Front
Center
Surround
Speakers
Enter ReturnENTER
BACK
4
Press SETUP.
The menu display disappears.
Bass
Default settings are underlined.Default settings are underlined.