Filter
Top Products
About MP3
MP3 (MPEG 1 Audio Layer-3) is a standard
technology and format for compressing a sound
sequence. Each file, or track, is compressed to
one-tenth of its original size.
In order to play MP3 files in the Delphi CD Audio
System, files must have been created according
to the following requirements:
Usable media – CD-Rs and CD-RWs
Usable disc format – ISO 9660 Level 1, Level 2,
and Joliet extension format discs
Maximum number of directories: 255
Maximum number of files: 255
AM/FM Radio Operation
Listening to AM/FM Radio
To listen to AM/FM radio stations:
1. Rotate the central unit so that the CD panel faces
forward. Be sure to follow the arrows when
rotating the unit. Complete the rotation until the
unit locks in position. CAUTION: Do not use
excessive force, which could damage the unit.
2. Press “Power” on the CD panel or remote control.
3. Press “Mode” on the CD panel or “CD/AM/FM”
on the remote control to select AM/FM mode.
4. Press “Stop” on the CD panel or “CD/AM/FM”
on the remote until the desired band (AM or FM)
appears in the display.
5. Press “Tune,” “Seek,” or “Scan” on the CD
panel or the category keys on the remote until
the desired station frequency shows in the display.
Storing AM/FM Stations in Memory
To store AM/FM stations in memory:
1. Select the desired AM/FM station.
2. Press “Memory” on the CD panel or
“mem/prog” on the remote.
3. With station frequency flashing on the display,
press “Tune” on the CD panel or “prev/next”
on the remote to select the desired memory
location (FM 1 to 18; AM 1 to 12).
4. Press “Memory” or “mem/prog” again to select.
Figure 13: Display While Storing AM/FM Stations in Memory
*Refer to the
SKYFi Operating Guide
for more specific information on
operating your SKYFi Receiver.
Seeking/Scanning
To search AM/FM stations manually:
Press “Tune” on the CD panel or “seek/random” on
the remote. The frequency increases one step (200
KHz for FM or 10 KHz for AM) with each press. The
display will repeat from the minimum if it reaches the
maximum frequency. If the selected station matches
one already stored in memory, the memory location
(FM 1 to 18; AM 1 to 12) will display.
To search stations stored in memory one by one:
1. Press “Scan” on the CD panel or “display/scan”
on the remote. If the received signal is strong, it
will stay tuned for 5 seconds with the station
frequency flashing.
2. Press “Scan” or “display/scan” a second time to
select the station or allow the next station in
memory to play automatically. Stored stations
will continue to scan in this way until one is
selected or until the tuner has returned to the
initial (INT) frequency. “INT” will show in the
display.
Adjusting the Tone (Bass and Treble)
Adjusting the Bass Level
To adjust the bass level:
1. Press the Menu key on the CD panel or remote
to show Menu functions on the display.
2. Press the Menu key six times, then hold to enter
the BASS submenu.
3. Press the Vol+ key on the CD panel or the Vol+
key on the remote to increase bass 1 dB per step
to reach a maximum of +10 dB. Press the
—
Vol
key on the CD panel or Vol
—
key on the remote
to decrease bass 1 dB per step to reach a
minimum of -10 dB.
Activating Bass Boost (BBS)
To activate BBS:
1. Press the Menu key on the CD panel or remote
to show Menu functions on the display.
2. Press the Menu key five times, then hold to
enter the BBS submenu.
3. Press the Vol+ key on the CD panel or the Vol+
key on the remote to activate BBS. Press the
—
Vol key on the CD panel or the Vol
—
key on the
remote to turn BBS off.
6
SECT ION 3
FM
ST
CH03
102.2 MHz
MEMORY
Frequency band
Stereo signal received
indicator
Memory location
Frequency