Filter
Top Products
25-EN
01GB05CDA9883.fm
ALPINE CDA-9883 68-08564Z10-A (EN)
5
Turn the Rotary encoder to select a song and
press / /ENT.
The selected song is played back.
• After pressing and holding / /ENT for at least 2 seconds while
in each hierarchy (except SONG hierarchy), all songs of the selected
hierarchy are played back.
• After selecting [ALL] in the search mode with “*”, press and hold
//ENT for at least 2 seconds to play back all songs in the iPod
or selected search mode.
• While in the search mode, if you press and hold /ESC for at least
2 seconds, or no operation is performed for 10 seconds, the search
mode is canceled.
• In the search mode, pressing /RTN will return to the previous
mode.
• Search can not be made during M.I.X. play.
• “NO SONG” will be displayed if there is no song in the selected
playlist in the playlist search mode.
• “NO PODCAST” will be displayed if there is no podcast data in the
iPod in the PODCAST search mode.
• If “iPod name” stored in the iPod is selected in the desired playlist
search mode and / /ENT is pressed, you can search for all songs
in the iPod. Also, if you press and hold / /ENT for at least 2
seconds, all songs in the iPod are played back.
• Depending on the iPod, podcast search is not supported.
• If any one of the preset buttons (1 through 6) is pressed in the search
mode, a search can be made quickly by skipping to the specified
location. For details, refer to “Direct Search Function” on page 25.
Quick Search
You can search a song from all songs in the iPod without selecting an
album, artist, etc.
1
Press and hold
/
ESC
for at least 2 seconds to
activate the Quick Search mode.
2
Turn the Rotary encoder to select a desired song.
The selected song is played back immediately.
• While in the search mode, if you press and hold /ESC for at least
2 seconds, or no operation is performed for 10 seconds, the search
mode is canceled.
• If many songs are in iPod, it takes time to search for songs.
• If any one of the preset buttons (1 through 6) is pressed in the search
mode, a search can be made quickly by skipping to the specified
location. For details, refer to “Direct Search Function” on page 25.
Direct Search Function
The unit’s direct search function can be used to search for an album,
song, etc., more efficiently. In the Playlist/Artist/Album/Song/Podcast/
Genre/Composer mode, You can quickly target any song.
In the search mode, press any one of the preset
buttons (1 through 6) to quickly skip over a
designated percent of your song content.
Song search example:
If there are 100 songs in your iPod, they are divided into 6
groups using percentages (shown below). These groups are
assigned to preset buttons 1 through 6.
Example 1:
Suppose the song you are searching for is located at around the
middle (50%) of your library: press button 4 to jump to the 50th
song and turn the Rotary encoder to find the desired song.
Example 2:
Suppose the song you are searching for is located near the end
(83%) of your library: press button 6 to jump to the 83rd song
and turn the Rotary encoder to find the desired song.
Select Playlist/Artist/Album/Podcast/
Genre/Composer
Playlist/Artist/Album/Podcast/Genre/Composer can be easily changed.
For example, if you listen to a song from a selected album, the album
can be changed.
Press or to select the desired Playlist/Artist/
Podcast/Album/Genre/Composer.
• If the song search mode was used to select a song, this function is
inactive.
• If an album is selected during an artist search, other albums by that
artist are searchable.
• This function is inactive during shuffle (M.I.X.) playback.
All 100 songs (100%)
0% 17% 33% 50% 67% 83%
Preset
buttons
123456
Songs
First
song
17th
song
33rd
song
50th
song
67th
song
83rd
song
68-08564Z10-A_F.book Page 25 Tuesday, November 21, 2006 8:53 AM