Filter
Top Products
29-EN
( Left Rear (–) Speaker Output Lead (Green/
Black) (CDA-7867 only)
) Left Front (–) Speaker Output Lead (White/Black)
(CDA-7867 only)
~ Left Front (+) Speaker Output Lead (White)
(CDA-7867 only)
+ Ai-NET Connector
Connect this to the output or input connector of other
product (CD Changer, Equalizer, etc.) equipped with
Ai-NET.
NOTE
You can input TV/video sound by connecting an optional
Ai-NET/RCA Interface cable (KCA-121B) to this
component.
, DC/DC Converter
NOTES
• Do not install the converter at a location subjected to
water such as under the floor mat or air conditioner.
This may cause a malfunction.
• Do not bundle the DC/DC converter cable with other
audio cables. Doing so may induce noise into your
system.
- Ai-NET Cable (Included with CD Changer)
. Front Output RCA Connectors
RED is right and WHITE is left.
/ Rear Output RCA Connectors
RED is right and WHITE is left.
: Subwoofer RCA Connectors
RED is right and WHITE is left.
; RCA Extension Cable (Sold Separately)
< System Switch
When connecting an equalizer or divider using Ai-
NET feature, place this switch in the EQ/DIV
position. When no device is connected, leave the
switch in the NORM position.
NOTE
Be sure to turn the power off to the unit before changing
the switch position.
= The Digital Output Connector (CDA-7969 only)
Connect this to any other optical digital products of
ALPINE.
The digital signal will be output when the CD mode is
on.
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove the coating if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries
various Alpine noise suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
1 Antenna Receptacle
2 Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power
antenna, if applicable.
NOTE
This lead should be used only for controlling the
vehicle's power antenna. Do not use this lead to turn on
an amplifier or a signal processor, etc.
3 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
4 Audio Interrupt In Lead (Pink/Black)
5 Illumination Lead (Orange)
This lead may be connected to the vehicle's
instrument cluster illumination lead. This will allow
the backlighting of the CDA-7969/CDA-7867 to dim
whenever the vehicle's lights are turned on.
6 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle's
fuse box or another unused power source which
provides (+)12V only when the ignition is turned on
or in the accessory position.
7 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the
vehicle's battery.
8 Ground Lead (Black)
Connect this lead to a good chassis ground on the
vehicle. Make sure the connection is made to bare
metal and is securely fastened using the sheet metal
screw provided.
9 Fuse Holder
• CDA-7969 .... 7.5A
• CDA-7867 .... 15A
! Power Supply Connector
" Right Front (+) Speaker Output Lead (Gray)
(CDA-7867 only)
# Right Front (–) Speaker Output Lead (Gray/
Black) (CDA-7867 only)
$ Right Rear (–) Speaker Output Lead (Violet/
Black) (CDA-7867 only)
% Right Rear (+) Speaker Output Lead (Violet)
(CDA-7867 only)
& Left Rear (+) Speaker Output Lead (Green)
(CDA-7867 only)