Chapter 4 Recording/Playback
45
4-1 Recording
1
Watching the indicators above the time data display,
press the COUNTER SEL button to select TC.
2
Press the HOLD button.
The SHUTTLE button lights and the first two digits of
the time code shown in the time data display start
flashing.
To set all digits to 0
Press the RESET button.
3
Select the digits to set by rotating the shuttle dial or jog
dial.
The flashing digits change to the next two digits on the
right when you rotate the shuttle dial or jog dial
clockwise, and to the next two digits on the left when
you rotate it counterclockwise.
4
Set the value for the flashing digits by rotating the
shuttle dial or jog dial while holding the SHUTTLE
button.
5
Repeat steps 3 and 4 until you finish setting all digits.
6
Press the SET button.
• An initial time code value is set and the monitor
returns to the time code display before the HOLD
button was pressed in step 2.
• If the F-RUN/R-RUN switch is set to F-RUN, the
time code starts advancing from the initial value
immediately.
To set time code to the time of the internal clock
You can record time code synchronized to the time of the
internal clock.
To do so, set the INT/EXT/RP188 switch to INT, set the
PRESET/REGEN switch to PRESET, and then proceed as
follows.
1
Carry out steps 1 and 2 of the previous section, “To
record time code after setting an initial value.”
2
With the SHUTTLE button held down, rotate the jog
dial in the counterclockwise direction. Stop rotating
when “CLOCK” appears in the time data display and
the video panel.
3
Press the SET button.
To set user bits
You can record up to eight hexadecimal digits of
information (date, time, clip name, etc.) in the time code
track.
Proceed as follows.
1
Watching the indicators above the time data display,
press the COUNTER SEL button to select UB.
2
Carry out steps 2 to 6 of the section “To set an initial
value” (page 44).
Settings are made in hexadecimal (0, 1, 2,... 8, 9, A,
B,... E, F).
AUDIO
VIDEO
INPUT SEL
WARNING
KEY INHI REC INHI
INPUT CH INPUT SEL STATUS LIGHT MONITOR
HLOFFOFFON
OFFON
-30
dB
-12
-20
-40
-60
0
CH
- 15
DATA
OVER
-30
dB
-12
-20
-40
-60
0
CH-
26
DATA
OVER
-30
dB
-12
-20
-40
-60
0
CH-
37
DATA
OVER
-30
dB
-12
-20
-40
-60
0
CH-
48
BATT E F
DATA
OVER
VITC
HOURS MINUTES SECONDS FRAMES
COUNTER HOLDVIUB
PB EXT-LKNDF
DISC E B
ACCESS
SHUTTLE JOG
THUMB
NAIL
ESSENCE
MARK
MENU
S.SEL
SET
RESET
SHIFT
TOP F REV
ALL/CH-1 CH-2 CH-3 CH-4
TC
F FWD
AUDI O
END
REC
PRESET
VARIABLE
PB
PREV NEXTPLAY STOP REC
CLIP
MENU
SYSTEM
MENU
MONITOR
SEL
METER
SEL
HOLD
COUNTER
SEL
SUB
CLIP
MARK1
MARK2
IN
OUT
KEY INHI
ON
OFF
NETWORK
LOCAL
REMOTE
F-RUN
R-RUN
PRESET
REGEN
INT
EXT
RP188
L/ST/R
CHARACTER
VITC
PROCESS
CONTROL
3,46
12
4
Time data display
SHUTTLE button
RESET button
AUDIO
VIDEO
INPUT SEL
WARNING
KEY INHI REC INHI
INPUT CH INPUT SEL STATUS LIGHT MONITOR
HLOFFOFFON
OFFON
-30
dB
-12
-20
-40
-60
0
CH
- 15
DATA
OVER
-30
dB
-12
-20
-40
-60
0
CH-
26
DATA
OVER
-30
dB
-12
-20
-40
-60
0
CH-
37
DATA
OVER
-30
dB
-12
-20
-40
-60
0
CH-
48
BATT E F
DATA
OVER
VITC
HOURS MINUTES SECONDS FRAMES
COUNTER HOLDVIUB
PB EXT-LKNDF
DISC E B
ACCESS
SHUTTLE JOG
THUMB
NAIL
ESSENCE
MARK
MENU
S.SEL
SET
RESET
SHIFT
TOP F REV
ALL/CH-1 CH-2 CH-3 CH-4
TC
F FWD
AUDI O
END
REC
PRESET
VARIABLE
PB
PREV NEXTPLAY STOP REC
CLIP
MENU
SYSTEM
MENU
MONITOR
SEL
METER
SEL
HOLD
COUNTER
SEL
SUB
CLIP
MARK1
MARK2
IN
OUT
KEY INHI
ON
OFF
NETWORK
LOCAL
REMOTE
F-RUN
R-RUN
PRESET
REGEN
INT
EXT
RP188
L/ST/R
CHARACTER
VITC
PROCESS
CONTROL
1
Time data display
