A SERVICE OF

logo

Open as PDF
next previous
12
E
Turning Power On/Off
Caution
• TurnonthemonitorrstbeforeturningonthePCor
playback device.
Turning on the main power
Main power switch
Caution
• Themainpowermustbeturnedon/offwiththemainpower
switch.Donotconnect/disconnectthepowercordorturn
the breaker on/off while the main power switch is on.
• WhenswitchingthemainpowerswitchorthePOWER
buttonoffandbackon,alwayswaitforatleast5seconds.
Turning power on/off
PressthePOWERbuttonontheremotecontrolunitorthe
monitor itself to turn the power ON/OFF.
Whenthemainpowerswitchisoff,themonitorcannotbe
turnedonusingthePOWERbuttonontheremotecontrolunit.
Power LEDPower button
Status of a power LED Status of the monitor
Green lighting Power on
Orange lighting Power off (Standby mode)
Greenashing Input signal waiting mode
Caution
• WhenswitchingthemainpowerswitchorthePOWER
buttonoffandbackon,alwayswaitforatleast5seconds.
A short interval may result in a malfunction.
TIPS
• Ifthemonitorisintheinputsignalstandbymodeandyou
pressthePOWERbuttonontheremotecontrolunit,the
monitor enters standby mode.
• SettingtheSCHEDULEashesthepowerLEDalternately
in red and orange in standby mode.
• IfyouchangetheremotecontrolmodetoALLMONITORS,
power can be turned ON/OFF for all slave monitors
connectedwithRS-232cable.(Foroperationofthemaster
monitor, use the buttons on the monitor itself.)
n
Operation mode
Whenthemonitoristurnedonforthersttimeafterbeing
shipped from the factory, the operation mode setting screen
willbedisplayed.SetittoMODE1orMODE2.
MODE1 ....
Limitsthemaximumbrightnesstoapprox65%ofMODE2.
OFFIFNOOPERATIONissettoON,andSTANDBY
MODEissettoLOWPOWER2.(Thesesettingscannot
be changed.)
If there is no operation for 4 hours or more, the monitor
automatically enters standby mode. Power consumption
instandbymodeisalsominimized.
MODE2 ....Willperformstandardoperation.
OFF IF NO OPERATION is set to OFF, and
STANDBYMODEissettoSTANDARD.These
settings can be changed.
Even after being set, changes can be made using
OPERATIONMODE,locatedinthemainmenuofthemonitor.
(See Operation Guide.)
n
Date/time setting
•
Ifthetimehasyettobesetwhenthemonitorisrstturnedon,
the date/time setting screen appears. Set the date and time.
DATE/TIME SETTING
SET
CANCEL
10
//
OK···[MENU]
20
01
/
01
/
00 00
:
: :
1. Press , , or to select the date and
time, and press
or to change the numerical
values.
2. Select SET and then press
MENU
.
• Besuretosetthedateandtime.
•
The date/time setting screen will close automatically if no
operationisperformedforabout15seconds.Thedate
andtimecanbesetusingDATE/TIMESETTINGfromthe
OPTION menu when the date/time setting screen disappears.
TIPS
•
Setthedatein“Year/Month/Day”order.
•
Setthetimeona24-hourbasis.
•
The clock is maintained by the internal battery.
•
If you already set the time but the date/time setting
screen appears when the power is turned on, the
internal battery may be exhausted. Please contact
your local Sharp servicing dealer or service center for
assistance with battery replacement.
•
Estimatedservicelifeoftheinternalbattery:About5
years (depending on monitor operation)
•
Astherstbatterywasinsertedatthefactory,itmaybe
exhausted prior to the expected continuous operation life.
Disabling power on/off operations
Power on/power off operations can be disabled in order to protect
themonitorfromanaccidentalpoweroff.SettheADJUSTMENT
LOCKinFUNCTIONmenuto“2”.(SeeOperationguide.)