For more information visit our website at www.polkaudio.com 41
40 Polk Audio Customer Service: 1-800-377-7655 (Outside US & Canada: 410-358-3600) Monday-Friday, 9:00 AM-6:00 PM EST, polkcs@polkaudio.com
Hookup
OPTIONAL
CHANNEL 1
CHANNEL 2
NETWORK IN
COMM
CHANNEL 1
CHANNEL 2
NETWORK IN
COMM
CONTROL CFG CHANNEL
Y
N
A
B
1
2
CONTROL CFG CHANNEL
Y
N
A
B
1
2
1
2
3
4
5
Disconnect all cables.
Disconnect all cables.
Disconnect all cables.
Disconnect all cables.
Disconnect all cables.
Disconnect all cables.
Remove the (4) Torx screws (size T-10) holding the heat
sink to the amp housing. Set the screws safely aside.
Remove the (4) Torx screws (size T-10) holding the heat
sink to the amp housing. Set the screws safely aside.
Remove the (4) Torx screws (size T-10) holding the heat
sink to the amp housing. Set the screws safely aside.
Remove the (4) Torx screws (size T-10) holding the heat
sink to the amp housing. Set the screws safely aside.
Remove the (4) Torx screws (size T-10) holding the heat
sink to the amp housing. Set the screws safely aside.
Remove the (4) Torx screws (size T-10) holding the heat
sink to the amp housing. Set the screws safely aside.
Disconnect the ribbon cable from the
break-out board. Remove the amplifier
and loose cables from the amp housing.
Disconnect the ribbon cable from the
break-out board. Remove the amplifier
and loose cables from the amp housing.
Disconnect the ribbon cable from the
break-out board. Remove the amplifier
and loose cables from the amp housing.
Disconnect the ribbon cable from the
break-out board. Remove the amplifier
and loose cables from the amp housing.
Disconnect the ribbon cable from the
break-out board. Remove the amplifier
and loose cables from the amp housing.
Disconnect the ribbon cable from the
break-out board. Remove the amplifier
and loose cables from the amp housing.
Turn the amplifier over and remove the two screws
from the two metal standoffs located on the PCB.
Turn the amplifier over and remove the two screws
from the two metal standoffs located on the PCB.
Turn the amplifier over and remove the two screws
from the two metal standoffs located on the PCB.
Turn the amplifier over and remove the two screws
from the two metal standoffs located on the PCB.
Turn the amplifier over and remove the two screws
from the two metal standoffs located on the PCB.
Turn the amplifier over and remove the two screws
from the two metal standoffs located on the PCB.
Install the network decoder card on the standoffs, mating the
two sides of the 40-pin connector. Press down and ensure that
the card snaps onto the two plastic standoffs.
Install the network decoder card on the standoffs, mating the
two sides of the 40-pin connector. Press down and ensure that
the card snaps onto the two plastic standoffs.
Install the network decoder card on the standoffs, mating the
two sides of the 40-pin connector. Press down and ensure that
the card snaps onto the two plastic standoffs.
Install the network decoder card on the standoffs, mating the
two sides of the 40-pin connector
. Pr
ess down and ensur
e that
the card snaps onto the two plastic standoffs.
Install the network decoder card on the standoffs, mating the
two sides of the 40-pin connector. Press down and ensure that
the card snaps onto the two plastic standoffs.
Install the network decoder card on the standoffs, mating the
two sides of the 40-pin connector
. Pr
ess down and ensur
e that
the card snaps onto the two plastic standoffs.
6
Secure the network decoder card by reinserting the
two standof
f scr
ews into the two metal standof
fs.
Secure the network decoder card by reinserting the
two standoff screws into the two metal standoffs.
Secure the network decoder card by reinserting the
two standoff screws into the two metal standoffs.
Secure the network decoder card by reinserting the
two standof
f scr
ews into the two metal standoffs.
Secure the network decoder card by reinserting the
two standoff screws into the two metal standoffs.
Secur
e the network decoder car
d by r
einser
ting the
two standoff screws into the two metal standoffs.
7
Reinstall the amplifier onto the amplifier
chassis (reversing steps 1, 2 & 3).
Reinstall the amplifier onto the amplifier
chassis (reversing steps 1, 2 & 3).
Reinstall the amplifier onto the amplifier
chassis (reversing steps 1, 2 & 3).
Reinstall the amplifier onto the amplifier
chassis (r
eversing steps 1, 2 & 3).
Reinstall the amplifier onto the amplifier
chassis (reversing steps 1, 2 & 3).
Reinstall the amplifier onto the amplifier
chassis (r
eversing steps 1, 2 & 3).
OPTIONAL
CHANNEL 1
CHANNEL 2
NETWORK IN
COMM
CHANNEL 1
CHANNEL 2
NETWORK IN
COMM
CONTROL CFG CHANNEL
Y
N
A
B
1
2
CONTROL CFG CHANNEL
Y
N
A
B
1
2
Hookup
standoffs
