Rotary Lawnmower Owners Manual
Safety
Operation
Assembly
Maintenance
Model No. M46
WARNING • PLEASE READ
For your own safety please read this manual before attempting to operate your new unit.
Failure to follow instructions can result in serious personal injury. Spend a few moments to
familiarize yourself with your mower before each use.
9096-305209
Model No. M46
AU
7
Please refer to the following sections when preparing the mower for it’s first use.
GRASS CATCHER
1. Position the two catcher halves as shown in
(Figure 1A).
Align the locating lugs marked 1 & 2 at the front of the
catcher. With the catcher base on the ground, push the
top section on each side of locator lug 1 until it clicks into
place. (Figure 1B).
Repeat this process for locator lug 2
2. Continue working from the front and push each locator lug
into position from number 1 through 8 until completed. i.e.
start with locator lug number 1 then 2, 3, 4, 5, 6, 7, and 8.
(Figure 1A)
3. WARNING:
DO NOT HIT THE CATCHER WITH YOUR HAND OR A
MALLET. This will break the plastic.
ALWAYS START AT POSITION 1. Do not try to assemble
the catcher from any other starting point as this will make
it difficult to assemble the clips.
4. Before use, check that all the lugs are completely clipped.
Test the assembly by holding the top handle and pushing
down of the base of the catcher. (Figure 1C)
FOLDING HANDLE
1. Lift the locking lever to release the handle bars for folding.
(Fig. 1D)
2. Push the locking lever closed to lock the handle bars in
the operating position.
3. Adjust the tension by turning the lock nut with an AF spanner
GRASS CATCHER
1. To fit: Raise FLAP, grasp HANDLE and position catcher
against rear of mower.
2. To remove: grasp handle, lift FLAP, remove catcher. (Fig.1E)
AU
GRASS CATCHER
1. Position the two catcher halves as shown in
(Figure 1A).
Align the locating lugs marked 1 & 2 at the front of the
catcher. With the catcher base on the ground, push the
top section on each side of locator lug 1 until it clicks into
place. (Figure 1B).
Repeat this process for locator lug 2
2. Continue working from the front and push each locator lug
into position from number 1 through 8 until completed. i.e.
start with locator lug number 1 then 2, 3, 4, 5, 6, 7, and 8.
(Figure 1A)
3. WARNING:
DO NOT
HIT THE CATCHER WITH YOUR HAND OR A
MALLET. This will break the plastic.
ALWAYS START AT POSITION 1. Do not try to assemble
the catcher from any other starting point as this will make
it difficult to assemble the clips.
4. Before use, check that all the lugs are completely clipped.
Test the assembly by holding the top handle and pushing
down of the base of the catcher. (Figure 1C)
FOLDING HANDLE
1. Lift the locking lever to release the handle bars for folding.
(Fig. 1D)
2. Push the locking lever closed to lock the handle bars in
the operating position.
3. Adjust the tension
by turning the lock nut with an AF
spanner
GRASS CATCHER
1. To fit: Raise FLAP, grasp HANDLE and position catcher
against rear of mower.
2. To remove: grasp handle, lift FLAP, remove catcher. (Fig.
1E)
Figure. 1A
Figure. 1B
Figure. 1C
Figure. 1D
Figure. 1E
Locking
Lever
ASSEMBLY INSTRUCTIONS
Please refer to the following sections when preparing the mower for it’s first use.
7
ASSEMBLY INSTRUCTIONS
