Filter
Top Products
IntroductionPreparationsBasic Operation
Advanced
Operation
Additional
Information
Appendix
18
Hookups
Others
■ IMPEDANCE SELECTOR switch
Select the position whose requirements your speaker system meets.
(Upper position)
FRONT EFFECT:
The impedance of each speaker must be 6Ω or higher.
<U.S.A. and Canada models>
REAR: The impedance of each speaker must be 4Ω or higher.
REAR CENTER: The impedance of the speaker must be 4Ω or higher.
<Except for U.S.A. and Canada models>
REAR: The impedance of each speaker must be 6Ω or higher.
REAR CENTER: The impedance of the speaker must be 6Ω or higher.
CENTER: The impedance of the speaker must be 4Ω or higher.
MAIN: If you use one pair of main speakers, the impedance of each speaker
must be 4Ω or higher.
If you use two pairs of main speakers, the impedance of each speaker
must be 8Ω or higher.
(Lower position)
FRONT EFFECT:
The impedance of each speaker must be 8Ω or higher.
REAR: The impedance of each speaker must be 8Ω or higher.
REAR CENTER:
The impedance of the speaker must be 8Ω or higher.
CENTER: The impedance of the speaker must be 8Ω or higher.
MAIN: <Except for Canada model>
If you use one pair of main speakers, the impedance of each speaker
must be 8Ω or higher.
If you use two pairs of main speakers, the impedance of each speaker
must be 16Ω or higher.
<For Canada model only>
The impedance of each speaker must be 8Ω or higher.
■ Connecting the AC power cord
Plug in this unit to a wall outlet when all connections are complete.
Caution:
• Do not use other AC power cords than the one provided. (U.S.A., Canada, and Singapore
models only)
■ AC OUTLETS
Use these to connect the power cords from your other components to this unit. The
power to the switched outlets is controlled by this unit’s STANDBY/ON
(SYSTEM POWER or STANDBY on the remote). These outlets will supply
power to any connected unit whenever this unit is turned on. The maximum power
(total power consumption of components) that can be connected to AC OUTLETS
is 100 W.
■ Voltage selector (General and China models)
The voltage selector on the rear panel of this unit must be set for your local main
voltage BEFORE plugging into the AC main supply.
WARNING
Do not change the IMPEDANCE
SELECTOR switch setting while the power to
this unit is on, otherwise this unit may be
damaged.
IF THIS UNIT FAILS TO TURN ON
WHEN THE STANDBY/ON SWITCH IS
PRESSED:
The IMPEDANCE SELECTOR switch may
not be set to either end. If so, set the switch to
either end when this unit is in the standby
mode.
G.
IMPEDANCE SELECTOR
VOLTAGE SELECTOR
SET BEFORE POWER ON
FRONT
REAR
REAR CENTER
CENTER
MAIN A OR B
A + B
: 6
Ω
MIN./SPEAKER
: 4
Ω
MIN./SPEAKER
: 4
Ω
MIN./SPEAKER
: 4
Ω
MIN./SPEAKER
: 4
Ω
MIN./SPEAKER
: 8
Ω
MIN./SPEAKER
FRONT
REAR
REAR CENTER
CENTER
MAIN A OR B
A + B
: 8
Ω
MIN./SPEAKER
: 8
Ω
MIN./SPEAKER
: 8
Ω
MIN./SPEAKER
: 8
Ω
MIN./SPEAKER
: 8
Ω
MIN./SPEAKER
: 16
Ω
MIN./SPEAKER
240
R
W
ER ON
N
./SPEAKER
N
./SPEAKER
N
./SPEAKER
N
./SPEAKER
N
./SPEAKER
N
./SPEAKER
N
./SPEAKER
N
./SPEAKER
N
./SPEAKER
N
./SPEAKER
N
./SPEAKER
IN./SPEAKER
AC OUTLETS
VOLTAGE SELECTOR
(General and China models)
AC Power Cord
(General, China, and Australia models)
IMPEDANCE SELECTOR switch
AC Power Cord
(U.S.A., Canada, and Singapore models only)