Filter
Top Products
7
COMPACT DISC OPERATION
PLAYING A CD
1. Press the POWER button [8] once to turn the unit on.
2. Set the FUNCTION switch [9] to “CD” mode.
3. Place a compact disc on the spindle, label side up. A 3” (8cm) disc may also be played
without an adaptor.
4. Push the CD compartment door back to the unit. The display will indicate “00:00” for a few
seconds. Then, the total number of tracks [28] and the CD playing time [30] will appear on the
display.
5. Press the PLAY/ PAUSE button [1] once to start playing from track 1 and the display indicates
the playing track number [28] and the CD playing time. When pressing the MODE/ REMAIN
button [7] once, the REMAIN indicator [33] appears and the display changes from playing
time to remaining time.
6. When the last track has been played, playing will be stopped automatically and the total
number of tracks and playing time will appear again.
NOTE:When no disc is in the CD player, “DISC” appears on the display and starts flashing.
Interrupt playing
Press PLAY/PAUSE button [1] once for temporarily stop and the displayed playing time is flashing.
Press the button again to resume playing from the same point.
Stop playing
Press STOP button [4] and the display returns to the total number of tracks and playing time.
NOTE: Never open the CD compartment door [26] while the CD is playing.
RANDOM PLAY (Remote control only)
1. Press the RANDOM button from the remote control unit during normal play and RANDOM
indicator appears on the display, tracks will be played in random order.
2. Press the RANDOM button again to cancel selection.
NOTE: When the unit is in MEMORY PLAY mode the RANDOM function cannot be set but the
RANDOM indicator will flash on the display for a few seconds.
REPEAT PLAY
1. Press the REPEAT/ MEM. Up button [6] before or during normal play to repeat the track. The
repeat function has 2 different modes.
– Press the REPEAT/ MEM. UP button once to enter to the REPEAT ALL mode and the
REPEAT indicator appears on the display. Track will be played in order and the entire disc
will be repeated endlessly.
– Press the REPEAT/ MEM. UP button twice to enter to the REPEAT ONE mode and the
REPEAT indicator is blinking on the display. The current track will be repeated endlessly.
2. To cancel repeat play, simply press the REPEAT/ MEM. UP button until the REPEAT indicator
disappears on the display.
SKIPPING FOR THE BEGINNING OF A TRACK
1. Press the B. SKIP/ TUNING DOWN/ ADJ. DOWN button [3] once during playing, the CD
will return to the beginning of the current track. If the button is pressed continuously before
playing starts, the CD will return to the previous track(s).
2. Press the F. SKIP/ TUNING UP/ ADJ. UP button [2] once during playing, the CD will move to
the beginning of the next track. If the button is pressed continuoulsy, the CD will move to the
following track(s).
SEARCH A PARTICULAR POINT OF A TRACK
1. Press and hold the F. SKIP/ TUNING UP/ ADJ. UP button [26] or B. SKIP/TUNING DOWN/
ADJ. DOWN button [3] (more than 0.5 sec.) to locate a particular point in a track during
playing by mointoring the high-speed cueing sound.
– Keep the F. SKIP/ TUNING UP/ ADJ. UP button pressed to go ahead.
– Keep the B. SKIP/ TUNING DOWN/ ADJ. DOWN button pressed to go back.
2. Release the button when you reach the point in the selection that you want.
MEMORY PLAY
This function allows you to play the track (up to 20 tracks) of a disc in any order or repeat the
same tracks 20 times.
1. Press the MEMORY/ CLOCK ADJ. button [5] when the disc is not turning and “P-01” appears
on the LCD display [11].
2. Press the F. SKIP/ TUNING UP/ ADJ. button [2] or B. SKIP/TUNING DOWN/ ADJ. button
[3] to select the desired track.
3. Press the MEMORY/ CLOCK ADJ. button again to store into the memory, than “P-02” appears
on the display.
4. Repeat steps 2 and 3 to enter desired tracks, up to a maximum of 20 selections, into the
program.
5. Press the PLAY/ PAUSE button [1] once to start playing.
6. After playing the selection of tracks, the display will return to the total number of tracks and
playing time. If you want to play the selection again, press the MEMORY/ CLOCK ADJ.
button and then the PLAY/ PAUSE button to start playing.
NOTE: Memory program will be cleared automatically under the following conditions:
- The power is turned off.
- Press the STOP button [4] under condition of memory setting.
- The CD compartment door [26] is opened.
- Other function (RADIO/ TAPE) is selected.
8