Southwing SA505 Headphones User Manual


 
reduce battery consumption. To do so,
press the Forwad [8] and Backward Buttons
[9] together and hold for 1 second. To re-
connect the Headset to the music device,
do the same again.
Battery life
To conserve battery life, your Headset features
an auto-sleep function. This function switches
the Headset off after 4 hours of inaction.
Once your Headset has entered auto-sleep, it
can be switched on again normally.
5. PUSH4
TM
CALL*
The Headset can save and dial a user
favourite number. To do so, you will first
need to save your favourite number on the
Headset. This can only be done when you
have received a call from this same number
into your Headset (not made through a hid-
den call). Once this received call has ended,
press and hold the Backward Button [9] for
3 seconds until you hear a series of tones.
The number from the last received call will
be stored.
Now you can make a direct call to this num-
ber at any time just by sliding the
Microphone [4] down and pressing
Backward Button [2] for 1 second.
Your Headset can also be configured with a
specific Push4
TM
call number or service.
With the Headset on, slide the Microphone
[4] down and then press the Forward Button
[8] 1 second to call directly to the pre-con-
figured number or phone service.
6. ADDITIONAL FUNCTIONS
Muting the microphone
During a call, press and hold the Volume +
Button [5] and the Volume - Button [6] at the
same time for 2 seconds. A tone will be
heard every 2 seconds during the call to
remind you that the microphone is muted.
Doing the same again will reactivate the
microphone.
Transferring a call to the phone*
Press the Play Button [7] 3 times during a
call to transfer the call to the mobile phone.
Pressing the Play Button one time again will
transfer the call back to the Headset.
Automatic call pick up
If you wish to have all of your calls accepted
automatically (without any button presses),
you can enable the automatic call pick up
mode. To activate this mode, press the Play
Button 5 times. When you receive an incom-
ing call, your Headset will automatically
answer the call. To turn off the automatic
call pick up, just follow the same steps.
Please note:
The audio quality of your voice (as heard by the
other party) will be improved by having the micro-
phone down during a call.
Battery Level Indicator
When the battery level is low, every 10 sec-
onds the Status Light [10] will flash red 3
times and a series of tones will be heard.
5
Please Note:
· Before pairing to a device, make sure the Headset
is not connected to any device
· You may connect the Headset with an audio source
and a mobile phone simultaneously. Please refer to
your mobile phone/music-player manual for details
regarding pairing/connecting Bluetooth enabled
devices.
· Mobile phones should be connected before music
players.
4. GENERAL USAGE
Changing Volume
To increase the volume, with the Headset
on, press Volume + Button [5]. To decrease
the volume, press the Volume - Button [6].
The Headset will remember all volume set-
tings even when it is switched off.
Accepting / rejecting* a call
When the phone rings (ring tone can be
heard in Headset), slide the Microphone [4]
down to accept the call. If the microphone
is already down, slide up and then down.
Press and hold the Play Button [7] for 1 sec-
ond to reject the call regardless of the posi-
tion of the microphone.
Calls can also be accepted on the mobile
phone. If your Headset is connected to the
phone, the call will automatically be trans-
ferred to the Headset.
If you are listening to music when you
accept a call, the music will be paused dur-
ing the call.
Please note:
The audio quality of your voice (as heard by the
other party) will be improved by having the micro-
phone down during a call.
Initiating a call from your mobile phone
Slide the Microphone [4] down and dial the
number as usual with your phone. If your
Headset is on and the phone has been cor-
rectly paired, it will transfer the call to your
Headset.
Initiating a call with voice dialling
You may be able to initiate the voice dialling
function from your Headset (your phone will
need to support voice dialling and voice
tags need to be entered, please see your
phone’s user guide). To activate, slide the
Microphone [4] down and press the Play
Button [7] one time. Once you hear the
voice dial beep, you will be able to speak
the name of the person you wish to call,
resulting in the call being initiated.
Ending a call
Slide the Microphone [4] up during a call
and the call will be ended. If the micro-
phone is already up, slide down and then
up. To cancel an outgoing call, press and
hold the Play Button [7] for one second.
Disconnecting from the phone*
You may wish to disconnect the Headset
from the phone in order to reduce battery
consumption. To do so, press the Play
Button [7] 3 times on the Headset when it is
not in an active call and is not playing
music. If you want to pick up a call, you first
need to re-connect the Headset. To do so,
press the Play Button [7] twice again on the
Headset.
Play / Stop music**
To play music, press the Play Button [7] one
time. To stop playing music, press the Play
Button 2 times.
Pause / Resume music**
To pause music while playing, press the
Play Button [7] one time. To resume, press
the Play Button one time again.
Music skip forward / backward**
To skip forward and backward one track or
go up or down in a play list, press the
Forward Button [8] or Backward Button [9]
one time.
Disconnecting from the music**
You may wish to disconnect the Headset
from the stereo music device in order to
4
* The features marked with asterisk are only possible with Bluetooth phones supporting the Bluetooth
®
Hands-free profile. Today, most Bluetooth
phones support this profile.
** The features marked with two asterisks are only possible with Bluetooth phones and Bluetooth adapters (dongles) supporting the Bluetooth
®
A2DP and AVRCP profiles.