Filter
Top Products
INSTALLING THE WOOFER
Before Installation: New Construction
For installations in new construction, Sonance recommends using
a Virtuoso FlexBracket (part# 92246) to reserve a location for the woofer.
The FlexBracket is nailed or screwed to the studs and serves as a guide for the
drywaller so that the woofer hole will be in the desired location once the
drywall is installed.
Before Installation: Retrofit
1. Determine the location for the woofer (see Woofer Placement on page 2).
2. Perform an obstruction survey to be certain that there are no studs,conduit,
pipes, heating ducts or air returns that will interfere with the speaker.
3.The cutout for the Virtuoso A800D woofer is 8
7
/16” (214mm) wide and
14½” (368mm) high. There also must be at least 3
7
/8” (99mm) depth
within the wall for the woofer.
4. Position the included cutout template where the woofer is to be located and
pencil an outline on the wall.
• If you are unsure about obstructions,drill a small hole in the center of the
outline and insert a coat hanger wire into the hole to feel-around for
possible obstructions.
5.Cut the hole using a drywall saw, and run the speaker wire between the
amplifier and the woofer location.
Installation
The Sonance Virtuoso A800D woofer features exclusive FastMount® tabs and
an integral RotoLock® mounting system for quick mounting directly into
existing walls (see Illustration 4).
WARNING: The edges of FastMount tabs are very sharp. Use caution
when handling the woofer.
1.Remove the paint plug from the speaker. Connect the speaker wire to the
terminals on the woofer. Double-check that you connected amplifier + to
speaker + and amplifier – to speaker –.
2. Make sure all the RotoLock clamps are in the full clockwise position so that
they are tucked within the mounting hole’s border. Insert the woofer into
the hole in the wall. The RotoLock system can accommodate a maximum
wall material thickness of 1¼”.
• The FastMount tabs will prevent the speaker from falling out of the
mounting hole, allowing the installer to let go of the woofer to pick-up
tools or other items (see Illustration 4).
Note: The FastMount tabs are designed for one-time use only. If the
speaker is removed from the mounting hole the FastMount tabs will
disconnect and remain inside the wall.
3.Tighten the six screws on the front of the woofer baffle. The RotoLock
clamps will automatically rotate into position and begin clamping the
woofer (see Illustration 4).
• When you notice resistance on the screws the woofer has been clamped
successfully.
Note: The woofer flange is designed to flex and conform to any small
imperfections in the wall surface. Do not tighten the screws so much
so that the flange bows-out.
Important: Always use low-torque settings; NEVER over-tighten.
4.Attach the grille after the woofer has been installed.Insert about half of the
grille into the groove at the edge of the woofer.Gently fit the remaining half
of the grille by working around the woofer, fitting the grille into the groove
as you go.
Note: You can adjust the torque applied to the RotoLock screws to
achieve a proper grille fit.
PAINTING THE WOOFER AND GRILLE
You can paint the woofer and grille before installing it, which will
eliminate the “paint scar”if the woofer ever needs to be removed for service.
You can also paint the woofer after installation, but before the grille is
attached. The Virtuoso A800D woofer comes from the factory fitted with a
plastic ‘paint plug’. Use the paint plug to protect the woofer driver while the
flange is being painted along with the wall.
Sonance always suggests painting the grille separately from the woofer. Before
painting, carefully remove the under-grille cloth. It is held in place with a light
tacking glue that makes it easy to remove.
Spray the grille with thinned paint (5 parts thinner to 1 part paint), being
careful not to plug the holes. Too heavy a coat of paint on the grille can
adversely affect the sound of the woofer.
Once the grille and flange are painted and dry, replace the under-grille cloth,
remove the paint plug from the woofer flange and install the grille.
3
INSTRUCTION MANUAL
SONANCE VIRTUOSO
®
D-SERIES
A800D 8” IN-WALL WOOFER
FastMount
Tabs
RotoLock
Clamps
Illustration 4: A800D Woofer Installation