Filter
Top Products
ENGLISH
18
Enter the test tone mode.
14
• Only when it is in available surround modes except
stereo mode, the volume level of each channel can
be adjusted easily with the test tone function.
Note: When the 6 CH DIRECT is selected as an
input source, the test tone function does not
work.
At each channel, adjust the level as desired
until the sound level of each speaker is
heard to be equally loud.
15
Cancel the test tone function.
16
Adjusting each channel level
Adjusting each channel level with test
tone
Select the desired channel.
11
Adjust the level of the selected channel
as desired.
12
Repeat the above steps 11 and 12 to
adjust other channel levels.
13
• The LFE level can be adjusted within the range of
-10~0 dB and other channel levels within the range of
-15~+15 dB.
• In general, we recommend the LFE level to be
adjusted to 0 dB. If the recommended levels seems
too high, lower the setting as necessary.
• If the channel display disappears, start from the above
step 11 again.
• Each time this button is pressed, the corresponding
channel is selected and displayed for 3 seconds as
follows;
Front Left Center Front Right Rear Right
(Dolby Digital L(FE)
)SubWoofer Rear Left
( ): Adjustable only when the digital signals from Dolby Digital program
source that includes LFE signal are input in the available surround
mode.
• When it is in the stereo, or the speaker setting is “N”,
center, rear or subwoofer channel will not be selected.
• The test tone will be heard from the speaker of each
channel for 2 seconds as follows;
Front Left Center Front Right
SUBwoofer
Rear Left Rear Right
• When the speaker setting is “N”, the test tone of the
corresponding channel is not available.
• When the selected decoding mode is not matched to the
input signal format, the test tone function cannot work.
or
CHANNEL
SELECTOR
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUST AUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
AUTO
CH. SEL
or
ADJUST
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUST AUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
CH. LEVEL
AUTO
• You can select the desired channel and adjust its level
with repeating the steps 11 and 12 in “Adjusting each
channel level” procedure.
or
ADJUST
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUST AUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
CH. LEVEL
AUTO
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUST AUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
T.TONE
AUTO
POWER
DISPLAY
SLEEPVIDEO1
123VIDEO2
456VIDEO3
789CD
T.TONE
0 P.SCANTUNER
DSP MODE
D.TIMEADJUST AUX
MUTE T.MON
CH. LEVEL
CH. SEL
MASTER VOLUME
REMOTE CONTROL UNIT RM-105
T.TONE
AUTO