Samson EX500 Speaker User Manual


 
9
EX500 STEREO SUB WITH POWERED SATELLITES
Operating the EX500
30
105
200
Hz
0
5
10
POWERED SUBWOOFER 500 WATTS
EX500
SAMSON
POWER
ON
OFF
A.C. MAINS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
POWER
RATING
115V/230V 50HZ/60Hz 500W
AVIS;
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
SERIAL
No.
60Hz
50Hz
230VAC
MADE IN CHINA
LEVEL
MONO
PEAK
SWEEP
RIGHT
LEFT
RIGHT
LEFT
BALANCED INPUTS BALANCED HIGH PASS OUTPUTS
STEREO
ENGINEERED AND DESIGNED
IN THE UNITED STATES
BY SAMSON TECHNOLOGIES
••
••
••
••
••
115VAC
30
105
200
Hz
0
5
10
POWERED SUBWOOFER 500 WATTS
EX500
SAMSON
POWER
ON
OFF
A.C. MAINS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
POWER
RATING
115V/230V 50HZ/60Hz 500W
AVIS;
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
SERIAL
No.
60Hz
50Hz
230VAC
MADE IN CHINA
LEVEL
MONO
PEAK
SWEEP
RIGHT
LEFT
RIGHT
LEFT
BALANCED INPUTS BALANCED HIGH PASS OUTPUTS
STEREO
ENGINEERED AND DESIGNED
IN THE UNITED STATES
BY SAMSON TECHNOLOGIES
••
••
••
••
••
115VAC
MONO
STEREO
MONO
STEREO
!
0
10
5
!
0
10
5
PL 1602
16 CHANNEL LINE MIXER
SAMSON TECHNOLOGIES CORP., NEW YORK, U.S.A.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
120V - 60 Hz 35W
POWER
RATING
AVIS:
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE
ON
OFF
MIC 3MAIN OUT
BALANCED 600 +4db
TIP + RING - SLEEVE GND
AUX
RETURNS
UNBALANCED 10K
1L
AUX SEND
UNBALANCED
2K +4db
2R
1L2R3L4R5L6R7L8R9L10R11L12R13L14R15L16R
INPUTS BALANCED 10K -30 to +4db TIP + RING - SLEEVE GND.
6R 5L 4R 3L 2R 1L
INSERTS TIP RETURN RING SEND
1
2
3
1
2
3
-40+4
0
-10
TRIM
-40+4
0
-10
TRIM
1L2R3L4RLRLR
BUS
INSERTS
MIXER LINKING
110
POWER
S / N
~115V(0.3A)
230V(0.15A)
50/60Hz 30W
MIC 1
PL1602 Mixer
EX500 EX500
EX20 EX20
Two EX500s can be used with any pair of powered full range enclosures like the Samson EX20 and EX30.
Below is a typical system set-up using two EX500s with a mixer and a pair of powered satellite loudspeakers.
The EX500s inputs and outputs utilize industry standard XLR connectors. For a detailed wiring diagram, see the
section EX500 Connections on page 12. Follow the steps below the diagram to set up your system.
Connect the mixers left output to the left-side
EX500s left input and the mixers right output to the
right-side EX500s right input. Now connect the left-
side EX500s left output to the input of the left pow-
ered satellite, and right-side EX500s right output to
the input of the right satellite. Switch both the
Stereo/Mono selector switches to the Stereo posi-
tion.
Now adjust the crossover SWEEP to the desired fre-
quency. For the Expedition EX20 & EX30 select 80-
100Hz. If you are using another brand of powered
speaker as satellites with the EX500, consult their
respective owners manuals for the recommended
crossover point.
Lower your mixers master outputs to all the way off.
Now set the level of your powered satellites up to the
normal operating level. Run an audio signal (like
some music from a CD) through your mixer and raise
the level to a comfortable listening volume. Now
slowly raise the EX500 Level control and listen to the
low frequency output. Adjust the EX500 to the level
to low frequency output that you like. Now when you
raise and lower your mixers output, the EX500 and
satellites will track at the same relative volume.
30
105
200
Hz
0
5
10
POWERED SUBW
O
LEVEL
MONO
PEAK
SWEEP
LEF
T
BALA
STEREO
••
••
••