Filter
Top Products
Operation
Signature Cinema™ SC-50d/SC-60d Installation/Operation Manual 51
PRE
L
IMINAR
Y
4.1
Using the On-Screen
Menus
To display the Main Menu, press the MENU button on the remote control or DHD
Controller front panel (Figure 2-3).
To select a menu item, use the and buttons on the remote control or DHD Controller
front panel to highlight it. Then, to confirm your selection, press ENTER on the remote
control or DHD Controller front panel.
The SC-50d/SC-60d OSD menus are arranged hierarchically, as shown in Figure 4-1.
Some menu options apply only to certain input signal types. For example, Phase and
Tracking can only be adjusted for RGB, Component video or SCART signals.
Figure 4-1. SC-50d/SC-60d OSD Menu Structure
4. Operation
Input Source
Composite 1
Composite 2
Composite 3
Component
HD 1
HD 2
SCART
HDMI 1
HDMI 2
HDMI 3
HDMI 4
Aspect Ratio
16:9
4:3
Letterbox
VirtualWide
Cinema
Virtual Cinema
Native
Picture
Brightness
Contrast
Color
Tint
Sharpness
Noise Filter
Input Position
Left/Right
Up/Down
Width
Height
Overscan
Overscan Mode
(Zoom/Crop)
Phase
(RGB/Component/SCART signals only)
Tracking
(RGB/Component/SCART signals only)
Memory
Presets
Recall ISF Night or ISF Day
Recall/Save Custom 1 or Custom 2
Reset Custom 1 and Custom 2 to Factory
Default
Sleep Timer
Off, 30 Minutes, 60 Minutes, 90 Minutes, 2
Hours or 4 Hours
Information
Signal
(read-only)System
Network
Field Service
Manufacturing
Calibration
Display Color
Gain
-100, -99... 0 ... 99, 100 (Red, Green, Blue)
Offset
Gamma
Mode
(Simple / Advanced)
Simple
(1.00, 1.01, 1.02 ... 2.20 ... 3.38, 3.39, 3.40)
Advanced
(0 (2.2 gamma curve),
1, 2, 3 ... 20 (custom gamma tables))
Lamp
Mode
(Power (recommended) / Intensity)
Power
(SC-50d = 150, 151, 152 ... 200W)
(SC-60d = 300, 301, 302 ... 350W ... 370)
Intensity
(0, 1, 2 ... 9999)
Color Temp
Simple
(3200K, 5500K, 6500K, 7500K or 9300K)
RVR 0, 1, 2 ... 9
Input Image
Brightness
-50, -49 ... 0 ... 49, 50
Contrast
Color
Tint
Sharpness
Input Color
Gain
-32, -31... 0 ... 31, 32
(HD 1, HD 2 and Component inputs only)
Offset
Chroma Delay
0, 1, 2 ... 7
(Composite inputs only)
Noise Filter 0, 1, 2 ... 63
Save ISF Night
Back / Confirm
Save ISF Day
Copy/Paste
Copy Settings
Paste Settings
Output Shift
Left/Right
-50, -49 ... 0 ... 49, 50
Up/Down
Width
-50, -49, 48 ... 0
Height
Image
Alignment
Corner Alignment Top Left / Top Right / Bottom Left / Bottom Right
Midpoint Alignment
Center / Top Middle / Left Middle / Right Middle /
Bottom Middle
Splash
Configure
Owner Name
ISF Calibrated
ISF Other
Splash Timer 5, 6, 7 ... 15 ... 59, 60
Splash Enable On/Off
OSD Position Hor. / Ver. 0, 1, 2 ... 100
Note: Default settings appear in bold type.