PYLE Audio PT-1601X Stereo Amplifier User Manual


  Open as PDF
of 5
 
CAUTION:
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE ONL
Y WITH SAME TYPE FUSE.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
CAUTION:
EQ OR MIXER
EQ OR MIXER
SWITCH IN “STEREO” POSITION
STEREO OPERATION
STEREO SIGNAL SOURCE
CH 2
CH 1
Bridged Mode Operation
This amplifier can operate in a mono bridged output mode, if
your speakers can handle the following power output levels:
As shown in the diagram below, connect the speaker's positive
(+) to the amplifier's red speakers left (1/2) terminals and
negative (-) to red speakers right (1/2) terminals.
The speaker right (+) on the amplifier is used as a negative (-)
terminal for a bridged connection.
NOTE: The extra amplifier output of 6.35mm phone
jacks can not be used for the bridged connection. It can only
be used in normal (non-bridged) operation as a stereo speaker
output.
MONO SIGNAL SOURCE
USE
CHANNEL 1
INPUT ONLY
CH 2
CH 1
MONO SIGNAL SOURCE
USE
CHANNEL 1
INPUT ONLY
SWITCH IN “BRIDGED” POSITION
MONO BRIDGED OPERATION
DO NOT USE
BLACK TERMINALS
5 - PYLE PRO
PT-1201X/1601X/2001X/4001X Amplifier
Owner’s Manual
SWITCH IN “MONO” POSITION
MONO OPERATION
Speaker connections
You can connect 4 Ohm, 8 Ohm or 16 Ohm speakers to
Channel 1 and/or Channel 2 of the amplifier. If you connect
two pairs of speakers, be sure to follow these guidelines:
• Speakers which are connected to the same channel are
part of a pair, and must be of the same impedance.
• Speakers connected to different channels are NOT part
of a pair, and can be of different impedances.
1. Prepare the speaker wire by removing about 1 inch of
insulation from the end of the speaker wire you intend to
connect to the amplifier. Then twist the exposed wire to
secure all the wire strands.
NOTE: Use 16-gauge speaker wire for lengths up to25
feet; 14-gauge wire for lengths over 25 feet. It is
recommended that you use the shortest length of wire
possible.
2. Connect the speaker wires to the speaker's positive and
negative terminals.
NOTE: Most speaker terminals are either color-coded
or have a mark that indicates the terminal's polarity.
Usually positive terminals are red or have a plus symbol
(+), and negative terminals are black or have a minus
symbol (-).
3. Connect the speaker wires to the amplifier's left and
right speaker terminals according to the terminal color
polarity.
Stereo or Mono Inputs
Your Pyle Pro amplifier can be operated in Stereo, Mono or
Bridged mode, depending on the input source. If the input
signal is mono, slide the Stereo/Mono/Bridged selector
switch to MONO and the signal will be routed through both
channels. If you wish to run the amplifier in bridged output
mode, slide the switch to Bridged.
PYLE PRO PT-1201X/1601X/2001X/4001X Amplifier Owner’s Manual - 4
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
CH 2
CH 1
CH 2
CH 1
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
MONO SIGNAL SOURCE
USE
CHANNEL 1
INPUT ONLY
CH-2 CH-1
CH-2 CH-1
OUTPUTS
CH-2
GND
CA
UT
ION
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
PLUG WITH
AN EXTENSION CORD RECEPTACLE
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE
CAUTION:
BRIDGE
CH-1
GROUND LIFT
GROUND LIFT
INPUTS
MONO
STEREO BRIDGE
12
3
HOT(+)
COLD(
-
)
GND(+)
BALANCED INPUTS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AC 120V 60HZ
~
CAUTION:
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE ONL
Y WITH SAME TYPE FUSE.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
CAUTION:
STEREO SIGNAL SOURCE
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
CH 2
CH 1
CH-2 CH-1
CH-2 CH-1
OUTPUTS
CH-2
GND
CA
UT
ION
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
PLUG WITH
AN EXTENSION CORD RECEPTACLE
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE
CAUTION:
BRIDGE
CH-1
GROUND LIFT
GROUND LIFT
INPUTS
MONO
STEREO BRIDGE
12
3
HOT(+)
COLD(
-
)
GND(+)
BALANCED INPUTS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AC 120V 60HZ
~
STEREO SIGNAL SOURCE
CH 2
CH 1
MONO SIGNAL SOURCE
USE
CHANNEL 1
INPUT ONLY
DO NOT USE
BLACK TERMINALS
MONO SIGNAL SOURCE
USE
CHANNEL 1
INPUT ONLY
use RCA jacks
use XLR/6.35 mm
combo jacks
CAUTION:
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE ONL
Y WITH SAME TYPE FUSE.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
CAUTION:
DO NOT USE
BLACK TERMINALS
MONO SIGNAL SOURCE
USE
CHANNEL 1
INPUT ONLY
CH-2 CH-1
CH-2 CH-1
OUTPUTS
CH-2
GND
CA
UT
ION
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
PLUG WITH AN EXTENSION CORD RECEPTACLE
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE
CAUTION:
BRIDGE
CH-1
GROUND LIFT
GROUND LIFT
INPUTS
MONO
STEREO BRIDGE
12
3
HOT(+)
COLD(
-
)
GND(+)
BALANCED INPUTS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AC 120V 60HZ
~
 previous