Filter
Top Products
The System Setup menu
07
37
En
The volume increases to the
0dB
reference level.
2 Adjust the level of the left channel.
This will be the reference speaker level, so you may want
to keep the level around
0dB
so that you’ll have plenty of
room to adjust the other speaker levels.
• After pressing
ENTER
, test tones will be output.
3 Select each channel in turn and adjust the levels (
+/
– 10dB )
as necessary.
Use
/
to adjust the volume of the speaker you
selected to match the reference speaker. When it sounds
like both tones are the same volume, press
to confirm
and continue to the next channel.
• For comparison purposes, the reference speaker will
change depending on which speaker you select.
• If you want to go back and adjust a channel, simply
use
/
to select it.
4 When you're finished, press RETURN.
You will return to the Manual MCACC setup menu.
Fine Speaker Distance
• Default setting:
3.0 m
(all speakers)
For proper sound depth and separation with your system,
it is necessary to add a slight bit of delay to some
speakers so that all sounds will arrive at the listening
position at the same time. The following setting can help
you make detailed adjustments that you may not achieve
using the
Manual speaker setup
below.
1 Select ‘Fine SP Distance’ from the Manual MCACC
setup menu.
2 Adjust the distance of the left channel from the
listening position.
3 Select each channel in turn and adjust the distance
as necessary.
Use
/
to adjust the delay of the speaker you selected
to match the reference speaker. The delay is measured in
terms of speaker distance from
0.1
to
9.0
meters.
Listen to the reference speaker and use it to measure the
target channel. From the listening position, face the two
speakers with your arms outstretched pointing at each
speaker. Try to make the two tones sound as if they are
arriving simultaneously at a position slightly in front of
you and between your arm span.
1
When it sounds like the delay settings are matched up,
press
to confirm and continue to the next channel.
• For comparison purposes, the reference speaker will
change depending on which speaker you select.
• If you want to go back and adjust a channel, simply
use
/
to select it.
4 When you're finished, press RETURN.
You will return to the Manual MCACC setup menu.
Standing Wave
• Default setting:
ON
Acoustic standing waves occur when, under certain
conditions, sound waves from your speaker system
resonate mutually with sound waves reflected off the
walls in your listening area. This can have a negative
effect on the overall sound, especially at certain lower
3.Manual MCACC
:Return
a.Fine Ch Level
b.Fine SP Distance
c.Standing Wave
d.EQ Adjust
e.EQ Professional
3a.Fine Channel Level
Please Wait... 20
Caution!
Loud test tones
will be output.
:Cancel
3a.Fine Channel Level
MCACC:M1. MEMORY 1
L(Reference)
+0.5dB
Enter:Next :Cancel
3a.Fine Channel Level
L +0.5dB (Reference)
R [ 0.0dB ]
C +1.0dB
SL [ -3.0dB ]
SR [ +10.0dB ]
SBL [ -10.0dB ]
SBR [ +9.5dB ]
SW [ -1.5dB ]
:Finish
Note
1• If you can’t seem to achieve this by adjusting the distance setting, you may need to change the angle of your speakers very slightly.
• For better audibility, the subwoofer emits a continuous test tone (oscillating pulses are heard from your other speakers). Note that it may be difficult
to compare this tone with the other speakers in your setup (depending on the low frequency response of the reference speaker).
3.Manual MCACC
a.Fine Ch Level
b.Fine SP Distance
c.Standing Wave
d.EQ Adjust
e.EQ Professional
:Return
3b.Fine SP Distance
MCACC:M1. MEMORY 1
L(Reference)
3.0 m
Enter:Next :Cancel
3b.Fine SP Distance
L
3.0 m
(
Reference
)
R [ 3.0 m ]
C
2.5 m
SL [ 3.0 m ]
SR [ 3.0 m ]
SBL [ 3.0 m ]
SBR [ 3.0 m ]
SW [ 3.0 m ]
:Finish
VSX_AX4AVi.book.fm 37 ページ ２００５年６月２０日 月曜日 午後６時２７分