Filter
Top Products
44
Basic Playback
Switching ANALOG/DIGITAL signal input
This switch moves the input fed to the receiver between analog, digital and AC-3 RF sources. You need to take
special care to switch to the appropriate input, when necessary. For example, the switch would have to be on
digital to use DOLBY DIGITAL, DTS surround sound and MPEG audio (VSX-D938TX only) but it would have to be
on analog to record from the analog out jacks on the receiver. On the VSX-D938TX, the default setting is AUTO
(which chooses digital when all three are available but foes with whatever is available if it is the only choice), on
the VSX-D908TX/D908TX-G is ANALOG.
1
Press SIGNAL SELECT on the remote control or on the
front panel to select the input signal corresponding to
the source component.
Each press switches the signal in the order below:
VSX-D938TX model
ANALOGAUTO
AC-3 RF
DIGITAL
VSX-D908TX/D908TX-G models
ANALOG
DIGITAL
2
While SIGNAL SELECT is set to DIGITAL, AC-3 lights
when a Dolby Digital signal is input, and DTS lights
when a DTS signal is input
SIGNAL
SELECT
DTS
SP
A
DIGITAL
SIGNAL
SELECT
AC-3
SP
A
DIGITAL
SIGNAL
SELECT
DTS
DIGITAL
SIGNAL
SELECT
MPEG
SP
A
DIGITAL
SIGNAL
SELECT
MPEG
DIGITAL
SIGNAL
SELECT
AC-3
DIGITAL
When a Dolby Digital
signal is input.
When a DTS signal is
input.
S0URCE
DVD/LD TV/SAT
VCR1 VCR2
CD
TV VOL
TV FUNC
MENU
ENTER
STEREO
DIGITAL NR
MIDNIGHT
ADVANCED STANDARD
DSP
THX
MUTE
TV
VOLUME
MD/
TAPE1
TUNER
TV CONT
RECEIVER
MULTI
OPERATION
CLASS MPX
MULTI CONTROL
DIRECT ACCESS
STATION
CHANNEL
TUNING
DISPLAYRF ATT
TV CONTROL
FUNCTION
SIGNAL
SELECT
EFFECT
/CH SEL
2/dts
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
REMOTE
SETUP
SYSTEM
SETUP
BAND
SYSTEM
OFF
1
23
4
56
7
+10
89
0
DISC
Î
¶
738
1¡4¢
+
-
+
-
+
-
MPEG
SIGNAL
SELECT
VSX-D938TX
• In the AUTO setting (VSX-D938TX only), SIGNAL SELECT
chooses the signal in the following order: AC-3 RF, DIGITAL,
ANALOG.
• If the Digital-In Select (see p.37) choices are set to OFF, the
SIGNAL SELECT will default to ANALOG.
• Because the audio from a karaoke microphone and LD
recorded with analog audio only is not output from the digital
output, set SIGNAL SELECT to “ANALOG”.
• This receiver can only play back Dolby Digital, PCM (32kHz,
44kHz, 48kHz, and 96kHz), DTS, or MPEG digital signal
formats. It cannot play back digital singals other than these so
for those formats you will have to play them back in an analog
manner (making sure your equipment is hooked up with
analog connections and setting the SIGNAL SELECT to
“ANALOG.”
• When an LD or CD with DTS is played back with the SIGNAL
SELECT set in “ANALOG,” digital noise caused by playing
back the DTS directly (with no decoding) is output. To prevent
noise, you need to make digital connections (See p. 10, 11)
and set SIGNAL SELECT to “DIGITAL”(VSX-D938TX could
also be set to “AUTO”).
• Some DVD players do not output DTS signals. For more
details, refer to the instruction manual supplied with your
DVD player.
STANDBY/ON
DSP
MODE
THX CINEMA ADVANCED STANDARD
STANDBY
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
Digital Signal Processor
STEREO
/DTS
PHONES
S-VIDEO
5-CHANNEL EQUAL POWER OUTPUT
VIDEO
EXTERNAL
DECODER INDIRECTLOUDNESS MIDNIGHT
DIGITAL
NR
SIGNAL
SELECT
INPUT ATTSPEAKERS
–
TREBLE +
–
BASS +
L AUDIO R
VIDEO INPUT
MPEG
VSX-D938TX
SIGNAL SELECT
When MPEG signal
is input.
VSX-D938TX only