Filter
Top Products
The System Setup menu06
28
En
Speaker setting
Use this setting to specify your speaker
configuration (size, number of speakers).
1 Select
SP SET
from the SP SETUP menu.
2 Use
/
to choose the speaker(s) that
you want to set then select a speaker size.
Use
/
to select the size (and number) of
each of the following speakers:
•
Front
(
F
) – Select
LARGE
if your front
speakers reproduce bass frequencies
effectively, or if you didn’t connect a
subwoofer. Select
SMALL
to send the bass
frequencies to the subwoofer.
1
•
Center
(
C
) – Select
LARGE
if your center
speaker reproduces bass frequencies
effectively, or select
SMALL
to send bass
frequencies to the other speakers or
subwoofer. If you didn’t connect a center
speaker, choose
NO
(the center channel is
sent to the front speakers).
•
Surround
(
S
) – Select
LARGE
if your
surround speakers reproduce bass
frequencies effectively. Select
SMALL
to
send bass frequencies to the other
speakers or subwoofer. If you didn’t
connect surround speakers choose
NO
(the sound of the surround channels is
sent to the front speakers or a subwoofer).
•
Surround Back
(
SB
) – Select the number
and size of surround back speakers you
have. Select
LARGE
if your surround back
speakers reproduce bass frequencies
effectively. Select
SMALL
to send bass
frequencies to the other speakers or
subwoofer. If you didn’t connect surround
back speakers choose
NO
.
2
•
Subwoofer
(
SW
) – LFE signals and bass
frequencies of channels set to
SMALL
are
output from the subwoofer when
YES
is
selected.
3
Choose the
PLUS
setting if you
want the subwoofer to output bass sound
continuously or you want deeper bass (the
bass frequencies that would normally
come out the front and center speakers are
also routed to the subwoofer). If you did not
connect a subwoofer choose
NO
(the bass
is output from other speakers).
Crossover network
• Default setting:
100Hz
This setting decides the cutoff between bass
sounds playing back from the speakers
selected as
LARGE
, or the subwoofer, and bass
sounds playing back from those selected as
SMALL
.
4
It also decides where the cutoff will
be for bass sounds in the LFE channel.
1 Select ‘
X.OVER’
from the SP SETUP menu.
2 Use
/
to choose the frequency cutoff
point.
Frequencies below the cutoff point will be sent
to the subwoofer (or
LARGE
speakers).
Channel level
Using these settings, you can adjust the overall
balance of your speaker system.
1 Select
CH LEVEL
from the SP SETUP menu.
2 Use
/
to select a setup option.
•
T. TONE M.
– Move the test tone manually
from speaker to speaker and adjust
individual channel levels.
Note
1 If you select SMALL for the front speakers the subwoofer is fixed to YES. Also, the center, surround, and surround back speak-
ers can’t be set to LARGE if the front speakers are set to SMALL. In this case, all bass frequencies are sent to the subwoofer.
2• If the surround speakers are set to NO, the surround back speakers will automatically be set to NO.
• If you selected SB 2ND Z or SB BIAMP (in Surround back speaker setting on page 27) you can’t adjust surround back settings.
• If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal.
3 If you can’t get good bass results, listen to the bass response with the subwoofer set to PLUS and YES or the front speakers
set to LARGE and SMALL alternatively and let your ears judge which sounds best. If you’re having problems, the easiest option
is to route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.
4 For more on selecting the speaker sizes, see Speaker setting above.
VSX_516.fm 28 ページ ２００５年１１月２９日 火曜日 午後１２時２７分