Filter
Top Products
Listening to your system
05
33
En
• While listening to a source, press
RECEIVER
, then
press
MCACC
.
Press repeatedly to select one of the six MCACC presets
1
or to switch calibration off. See Data Management on
page 46 to check and manage your current settings.
Choosing the input signal
You need to hook up a component to both analog and
digital inputs on the receiver to select between input
signals.
2
•Press
RECEIVER
, then press
SIGNAL SEL
to select
the input signal corresponding to the source
component.
Each press cycles through the options as follows:
• AUTO – This is the default setting. The receiver
selects the first available signal in the following order:
HDMI; DIGITAL; ANALOG.
• ANALOG – Selects an analog signal.
• DIGITAL – Selects an optical or coaxial digital signal.
• HDMI – Selects an HDMI signal.
3
• PCM – Only PCM signals are output.
4
When set to DIGITAL or AUTO, 2 DIGITAL lights with
Dolby Digital or Dolby Digital Plus decoding, 2 HD
lights with Dolby TrueHD decoding, DTS lights with DTS
or DTS-HD decoding, and WMA9 Pro lights to indicate
that a WMA9 Pro signal is being decoded.
Using surround back channel
processing
• Default setting: SBch ON
You can have the receiver automatically use 6.1 or 7.1
decoding for 6.1 encoded sources (for example, Dolby
Digital EX or DTS-ES), or you can choose to always use
6.1 or 7.1 decoding (for example, with 5.1 encoded
material). With 5.1 encoded sources, a surround back
channel will be generated, but the material may sound
better in the 5.1 format for which it was originally
encoded (in which case, you can simply switch surround
back channel processing off).
The table below indicates when you will hear the
surround back channel when playing various kinds of
sources (
=Sound plays through surround back
speaker(s)).
•Press
RECEIVER
, then press
SBch
repeatedly to
cycle the surround back channel options.
Each press cycles through the options as follows:
• SBch ON – 6.1 or 7.1 decoding is always used (for
example, a surround back channel will be generated
for 5.1 encoded material)
• SBch AUTO – Automatically switches to 6.1 or 7.1
decoding for 6.1 encoded sources (for example,
Dolby Digital EX or DTS-ES)
• SBch OFF – No sound is output from the surround
back speakers
Note
1 • These settings have no effect when headphones are connected.
• You can also press / to select the MCACC preset.
2 • This receiver can only play back Dolby Digital, PCM (32 kHz to 192 kHz), DTS (including DTS 96 kHz/24 bit) and WMA9 Pro digital signal formats. The
compatible signals via the HDMI terminals are: Dolby Digital, DTS, WMA 9 Pro, PCM (32 kHz, 44.1 kHz, 88.2 kHz and 96 kHz sampling frequencies), Dolby
TrueHD, Dolby Digital Plus, DTS-EXPRESS, DTS-HD Master Audio, SACD and DVD Audio (including 192 kHz). With other digital signal formats, set to
ANALOG (the MULTI CH IN and FM/AM).
• You may get digital noise when a LD or CD player compatible with DTS is playing an analog signal. To prevent noise, make the proper digital connections
(page 19) and set the signal input to DIGITAL.
• Some DVD players don’t output DTS signals. For more details, refer to the instruction manual supplied with your DVD player.
3 When the HDMI option in Setting the Audio options on page 71 is set to THROUGH, the sound will be heard through your TV, not from this receiver.
4 • This is useful if you find there is a slight delay before AUTO recognizes the PCM signal on a CD, for instance.
• When PCM is selected, noise may be output during playback of non-PCM sources. Please select another input signal if this is a problem.
THX STATUS PHASE
TV CTRL
ANT
AUDIO
DISPLAY
MPX
SIGNAL SEL
CH
RECEIVER
MEM
SIGNAL SEL
RECEIVER
INPUT
123
SLEEPMCACCGENRE
456
A.ATTSBchSR+
789
CLASS
MASTER
VOLUME
CH LEVELD.ACCESS
0
ENTER
SBch
8
TV CTRL
MAIN
ZONE 2
ANT
AUDIO
DISPLAY
MPX
SIGNAL SEL
CH
RECEIVER
MEM
RECEIVER
VSX-1018AH_KU.book 33 ページ ２００８年４月１７日 木曜日 午後２時３７分