Pioneer DEH-1300MP CD Player User Manual


 
Removing the front panel to protect your unit from
theft
1 Press the detach button to release the front
panel.
2 Push the front panel upward and pull it toward
you.
3 Always keep the detached front panel in a protec-
tion device such as a protection case.
Re-attaching the front panel
1 Slide the front panel to the left.
Make sure to insert the tabs on the left side of the
head unit into the slots on the front panel.
2 Press the right side of the front panel until it is
firmly seated.
If you cannot attach the front panel to the head
unit successfully, make sure that you are placing
the front panel onto the head unit correctly. For-
cing the front panel into place may result in da-
mage to the front panel or head unit.
Turning the unit on
1 Press SRC/OFF to turn the unit on.
Turning the unit off
1 Press SRC/OFFand hold until the unit turns off.
Selecting a source
1 Press SRC/OFF to cycle through the sources
listed below:
TUNER (tuner)CD (built-in CD player)AUX
(AUX)
Adjusting the volume
1 Turn SRC/OFF to adjust volume.
CAUTION
For safety reasons, park your vehicle when remov-
ing the front panel.
Note
When this units blue/white lead is connected to
the vehicles auto-antenna relay control terminal,
the vehicles antenna extends when this units
source is turned on. To retract the antenna, turn
the source off.
Menu operations identical
for function settings/audio
adjustments/initial settings
Returning to the ordinary display
Canceling the initial setting menu
! Press B(BAND/ESC).
You can also cancel initial settings by holding
down SRC/OFF until the unit turns off.
Tuner
Basic Operations
Selecting a band
1 Press B(BAND/ESC) until the desired band (F1,
F2, F3 for FM or AM) is displayed.
Manual tuning (step by step)
1 Press c or d.
Seeking
1 Press and hold c or d, and then release.
You can cancel seek tuning by briefly pressing c
or d.
While pressing and holding c or d, you can skip
stations. Seek tuning starts as soon as you re-
lease c or d.
Storing and recalling stations
for each band
% When you find a station that you want
to store in memory, press one of the preset
tuning buttons (1 to 6) and hold until the
preset number stops flashing.
Stored radio station frequency can be recalled
by pressing the preset tuning button.
# Press a or b to recall radio station frequen-
cies.
En
6
Section
02
Operating this unit
Function settings
% Press FUNC to select the function.
After selecting, perform the following proce-
dures to set the function.
BSM (best stations memory)
BSM (best stations memory) automatically stores the
six strongest stations in the order of their signal
strength.
Storing broadcast frequencies with BSM may replace
broadcast frequencies you have saved using 1 to 6 .
1 Press a to turn BSM on.
The six strongest broadcast frequencies are
stored in the order of their signal strength.
To cancel the storage process, press b.
LOCAL (local seek tuning)
Local seek tuni ng lets you tune in to only those radio
stations with sufficiently strong signals for good re-
ception.
1 Press a or b to turn local seek tuning on or off.
2 Press c or d to set the sensitivity.
FM: LOCAL 1LOCAL 2LOCAL 3LOCAL 4
AM: LOCAL 1LOCAL 2
The highest level setting allows reception of only
the strongest stations, while lower levels allow the
reception of weaker stations.
CD
Basic Operations
Playing a CD/CD-R/CD-RW
1 Insert the disc into the disc loading slot with the
label side up.
Ejecting a CD/CD-R/CD-RW
1 Press h.
Selecting a folder
1 Press a or b.
Selecting a track
1 Press c or d.
Fast forwarding or reversing
1 Press and hold c or d.
When playing compressed audio, there is no
sound during fast forward or reverse.
Switching between compressed audio and CD-DA
1 Press B(BAND/ESC).
Displaying text information
Selecting the desired text information
1 Press D(DISP/SCRL).
Scrolling the text information to the left
1 Press and hold D(DISP/SCRL).
Notes
! Depending on the version of iTunes used to
write MP3 files to a disc or media file types, in-
compatible text stored within an audio file
may be displayed incorrectly.
! Text information items that can be changed
depend on the media.
Function settings
% Press FUNC to select the function.
After selecting, perform the following proce-
dures to set the function.
RPT (repeat play)
1 Press c or d to select the repeat range.
DSC Repeat all tracks
TRK Repeat the current track
FLD Repeat the current folder
RDM (random play)
1 Press a or b to turn random play on or off.
When random play is on, RDM appears in the dis-
play.
If you turn random play on during folder repeat,
FRDM appears in the display.
SCAN (scan play)
Scan play searches for a song within the selected re-
peat range.
1 Press a to turn scan play on.
If you turn scan play on during FLD, FSCN ap-
pears in the display.
2 When you find the desired track press b to turn
scan play off.
If the display has automatically returned to the
playback display, select SCAN again by pressing
FUNC.
After scanning of a disc (folder) is finished, nor-
mal playback of the tracks begins.
PAUSE (pause)
1 Press a or b to pause or resume.
SRTRV (sound retriever)
En
7
English
Section
02
Operating this unit
<QRD3061-A/N>4