Filter
Top Products
3139 116 19591 (ENG)
19
STANDBY
ON
MINI HIFI SYSTEM
BANDC1 • 2 • 3
CDR
STOP•CLEAR
SEARCH•TUNING PLAY PAUSE PREV
NEXT
DUB
(HSD)
RECORD
A. REVDIM
CLOCK/
TIMER
PROG
BASS
TREBLE
wOOx
TECHNOLOGY
POWER SAVE
IR SENSOR
SIDE
V
O
L
U
M
E
PLUS
LEVEL
PRESET
▲
▲
B
A
S
S
/
T
R
E
B
L
E
TAPE
CD
TUNER
AUX
P
E
R
S
O
N
A
L
D
S
C
V
E
C
TAPE 1•2
CD 1•2•3
FM•AM
CDR/DVD
Note:
– For 'EASY SET' feature, please refer to
page 13.
Tuning to radio stations
1 Press TUNER (FM•AM) to select
TUNER mode.
™ "TUNER" will be displayed.
A few seconds later, the current
radio frequency will be displayed.
2 Press TUNER (FM•AM) again to
select the desired waveband : FM or
AM.
3 Press à or á for more than one
second, then release.
™ The display will show "SEARCH"
until a radio station with sufficient
signal strength is found.
• Repeat this procedure until the
desired radio station is reached.
• To tune to a weak radio station,
briefly press à or á repeatedly
until the display shows the desired
frequency and/or when the best
reception has been obtained.
Storing Preset Stations
You can store up to 40 radio stations in
the memory. When a preset radio
station is selected, the preset number
appears next to the frequency on the
display.
Automatic programming
1 Press TUNER (FM•AM).
2 Press PROG for more than one
second.
™ The PROGRAM starts flashing and
"AUTO" will be displayed.
TUNER
™ The system will search for every
available radio station in the FM
waveband first, then search the
AM waveband.
™ All available radio stations will be
stored automatically. The
frequency and preset number will
be displayed briefly.
™ The system will stop searching
when all the available radio stations
are stored or when the memory
for 40 preset radio stations is used.
™ The system will remain tuned to
the last stored preset radio station.
Notes:
– You can cancel the automatic
programming by pressing PROG or
Ç
(on the system only).
– If you want to reserve a section of
preset numbers, for example preset
numbers 1 to 9, select preset 10
before starting automatic programming,
only the preset numbers 10 to 40 will
be programmed.
Manual programming
1 Press TUNER (FM•AM).
2 Press TUNER (FM•AM) again to
select the desired waveband : FM or
AM.
3 Press PROG for less than one
second.
™ The PROGRAM starts flashing.
™ The next available preset number
will be displayed for selection.
4 Press à or á to tune to the
desired frequency.
• If you wish to store the radio station
to another preset number, press 4
or 3 (or Digit 0-9 on the remote
control) to select the desired preset
number.
5 Press PROG again.
™ The PROGRAM disappears and the
radio station will be stored.
• Repeat steps 3 – 5 to store other
preset radio stations.
Notes:
– When 40 radio stations are stored and
you attempt to store another radio
station, the display will show
"PROGRAM FULL". If you want to
change an existing preset number,
repeat steps 3 – 5.
– You can cancel manual programming
by pressing
Ç
(on the system only).
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Tuning to Preset Radio
Stations
• Press 4 or 3 (or Digit 0-9 on the
remote control) to select the desired
preset number.
™ The preset number, radio
frequency, and waveband appear
on the display.
pg 01-28/C85/37-Eng 2/16/00, 9:03 AM19