Philips FW-C50 Stereo System User Manual


 
3139 116 19441 (ENG)
15
If you wish to change the inner disc
during playback, press DISC
CHANGE again.
DISC CHANGE" will be
displayed.
The CD will stop playing.
The CD carousel tray will close to
retrieve the inner CD and then
open again with the inner CD
accessible.
3 Press OPEN•CLOSE to close the
CD carousel tray.
Selecting a desired track
Selecting a desired track when
playback is stopped
1 Press í or ë until the desired
track appears on the display.
2 PressÉ to start playback.
The selected track number and
elapsed playing time appear on
the display.
Selecting a desired track during
playback
Press í or ë until the desired
track appears on the display.
The selected track number and
elapsed playing time appear on
the display.
If you press í once it will skip to
the beginning of the current track
and play the track again.
Note:
Pressing
í
during shuffling can only skip
to the beginning of the current track.
Searching for a particular
passage during playback
Press and hold à or á until the
desired passage is located.
The volume will be reduced.
Play returns to normal when à or
á is released.
Programming Tracks
Programming tracks of a loaded CD is
possible when playback is stopped. The
display will indicate the total tracks
stored in the program. Up to 40 tracks
can be stored in the memory in any
order. When 40 tracks are stored and
you attempt to store another track, the
display will show “FULL”.
1 Load the desired discs in the disc
trays.
2 Press PROG to start programming.
The PROGRAM starts flashing.
It will cancel any previously
selected repeat mode.
3 Press the CD (CD 1•2•3) or DISC
1/2/3 button to select the disc.
4 Press í or ë to select the desired
track.
5 Press PROG to store the track.
Repeat steps 3 to 5 to store other
discs and tracks.
CD
6 Press Ç once to end programming.
The total number of tracks
programmed and total playing
time appear on the display.
Notes:
If the total playing time is more than
99:59 or if one of the
programmed tracks has a number
greater than 30, then “--:--
appears on the display instead of the
total playing time.
If the system is reading the disc,
programming is not possible,
READING” will be displayed and
followed by "DISC X" "X" is the
current read disc number.
During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Reviewing the program
Reviewing of the program is possible
only when playback is stopped.
Press í or ë repeatedly to review
the programmed tracks.
Press Ç once to exit review mode.
Playing the program
1 Press É to start program playback.
PLAY PROGRAM” will be
displayed.
The track number and elapsed
playing time of the current track
will appear on the display.
If you press REPEAT during
program playback, the current track
or all programmed tracks will be
played repeatedly.
TRACK” or "PROGRAM" will be
displayed.
The REPEAT and PROGRAM appear
on the display.
2 Press Ç to stop program playback.
Notes:
If you press any of the CD DIRECT
PLAY buttons, the system will play the
selected disc or track and the stored
program will be ignored temporarily.
The PROGRAM display also will
disappear temporarily from the display.
It will reappear when playback of the
selected disc ends.
REPEAT DISC mode will be cancelled
when program playback begins.
Erasing the program (when
playback is stopped)
Press Ç.
PROGRAM CLEARED” will be
displayed.
Note:
The program will be erased when the
system is disconnected from the power
supply or when the CD carousel tray is
opened.
pg 01-28/C50-C70/37-Eng 18/11/1999, 2:39 PM15