Filter
Top Products
17
English
Note:
– All the available discs will play once, then stop. When
the CD has stopped playing, the system will switch to
the standby mode after 15 minutes if no button is
pressed.
Disc Change
You can change the outer 2 discs while the third inner disc
is at the stop or playing mode.
1 Press DISC CHANGE.
™ The CD compartment slides out.
2 Replaced the discs in the left and right disc trays.
• If you press DISC CHANGE again during playback, the
CD will stop playing.
™ The CD carousel tray will rotate until the inner tray is
at the right hand side and is ready for changing.
3 Press OPEN•CLOSE to close the CD compartment.
Selecting a desired track
Selecting a desired track at the stop mode
1 Press PREV í or NEXT ë until the desired track
appears on the display.
2 Press PLAY É to start playback.
™ The selected track number and elapsed playing time
appear on the display.
Selecting a desired track during playback
1 Press PREV í or NEXT ë until the desired track
appears on the display.
™ The selected track number and elapsed playing time
appear on the display.
• If you press PREV í once it will skip to the beginning
of the current track and play the track again.
Searching for a particular passage
during playback
• Press and hold à or á until the desired passage is
located.
™ The volume will be reduced.
• Play returns to normal when à or á is released.
Programming Tracks
Programming tracks of a loaded CD is possible in the stop
mode. The display will indicate the total tracks stored in
the program. Up to 40 tracks can be stored in the memory
in any order. When 40 tracks are stored and you attempt to
store another track, the display will show “PROGRAM
FULL”.
1 Load the desired discs in the disc trays.
2 Press PROGRAM to start programming.
™ The PROGRAM flag starts flashing.
3 Press the CD (CD 1•2•3) button to select the disc.
4 Press PREV í or NEXT ë to select the desired track.
5 Press PROGRAM to store the track.
• Repeat steps
3
to
5
to store other discs and tracks.
6 Press STOP•CLEAR Ç once to end programming
mode.
™ The total number of tracks programmed and total
playing time appear on the display.
Notes:
– If the total playing time is more than “
99:59
” or if
one of the programmed tracks has a number greater
than 30, then “
--:--
” appears in the display instead
of the total playing time.
– During programming, if no button is pressed within 20
seconds, the system will exit program mode
automatically.
Playing the program
1 Press PLAY É to start program playback.
™ “PLAY PROGRAM” appears on the display.
™ The track number and elapsed playing time of the
current track will appear on the display.
• If you press REPEAT during program playback, the
current track will be played repeatedly.
™ The REPEAT and PROGRAM flags will be displayed.
2 Press STOP•CLEAR Ç to stop program playback.
Note:
– If you press any of the CD DIRECT PLAY buttons, the
system will play the selected disc or track and the
stored program will be ignored temporarily. The
PROGRAM flag will also temporarily disappear from the
display and then reappear when the playback for the
selected disc ends.
Reviewing the program
Reviewing of the program is only possible in the stop
mode.
• Press PREV í or NEXT ë repeatedly to review the
programmed tracks.
• Press STOP•CLEAR Ç to exit review mode.
Erasing the program (in the stop mode)
• Press STOP•CLEAR Ç on the system.
™ “PROGRAM CLEARED” will be displayed.
Note:
– The program will be erased when the system is
disconnected from the power supply. If the CD carousel
is opened, the tracks belonging to the outer two trays
will be erased and the display will show “
CLEARED
” .
CD