Filter
Top Products
RQTX0044
27
Using the FM/AM radio
Using the FM/AM radio
Radio operations are described mainly with the remote control.
You can alternatively use the corresponding button on the main unit.
§1
[SELECTOR]
§2
[X TUNING W]
§3
[MEMORY]
Up to 30 stations can be set in each band, FM and AM.
∫ If noise is excessive
When “FM” is selected
Press and hold [—FM MODE] on
the main unit to display
“MONO”.
Press and hold [—FM MODE] again to cancel the mode.
≥The mode is also canceled when you change the frequency.
When “AM” is selected
Press [FUNCTIONS] on the remote control.
Each time you press the button: BP 2()BP 1
∫ Presetting the channel
Up to 30 stations can be set in each band, FM and AM.
1 While listening to the radio broadcast
Press [ENTER]
§3
.
2 While the frequency and “PGM” are flashing on the display
Press the numbered buttons to select a channel.
≥To select a 2-digit number
e.g. 12:
[S10] ➜ [1] ➜ [2]
Alternatively, press [X, W], and then press [ENTER]
§3
.
A station previously stored is overwritten when another station is
stored in the same channel preset.
FM frequency step
\Main\unit\only]
The step is factory-set to 0.2-MHz, but you can change it to receive
broadcasts allocated in 0.1-MHz steps.
1 Press [SELECTOR] to select “FM”.
2 Press and hold [SELECTOR].
After a few seconds the display changes to show the current minimum
frequency. Continue to hold the button down. The minimum frequency
changes and the step is changed.
To return to the original step, repeat steps 1 and 2.
[Note]
After changing the setting, previously preset frequencies will be cleared.
Preset them again.
Presetting stations automatically
1
Press [TUNER/BAND]
§1
to select “FM” or “AM”.
2
Press and hold [ENTER]
§3
.
Release the button when “FM AUTO” or “AM AUTO” is displayed.
The tuner tunes to the lowest frequency and starts to preset all the
stations it can receive into the channels in ascending order.
≥“SET OK” is displayed when the stations are set, and the radio
tunes to the last preset station.
≥“ERROR” is displayed when automatic presetting is unsuccessful.
Preset the channels manually (➜ right).
Selecting the preset channels
1
Press [TUNER/BAND]
§1
to select “FM” or “AM”.
2
Press the numbered buttons to select the channel.
≥To select a 2-digit number
e.g. 12: [S10] ➜ [1] ➜ [2]
Alternatively, press [X, W].
≥To perform this step on the main
unit, first press [-TUNE MODE] to select “PRESET”, and then
press [X TUNING W] to select the channel.
When a stereo FM broadcast is being
received, “ST” lights in the display.
FUNCTIONS
ENTER
TUNER/BAND
,
,
Numbered
buttons
MEMORY
SELECTOR
TUNING
-TUNE MODE/ FM MODE
-
DISC
S.SRD
TG
KARA
D.MIX
MONO
SLP
U
SB
ODE
C
D
D
VD
O
SLP
STCT
RDS
RND
PGM
EQ
PRG
SRDE.
PL
DDTS
W1 W2
WS
Manual tuning
1
Press [TUNER/BAND]
§1
to select “FM” or “AM”.
2
Press [6, 5]
§2
to select the frequency.
≥When performing this step on the main unit, first press
[-TUNE MODE] to select “MANUAL”, and then press [
X
TUNING
W
]
to select the frequency.
≥To start automatic tuning, press and hold [6, 5]
§2
until the
frequency starts scrolling. Tuning stops when a station is found.
D.MIX
MONO
SLP
STCT
RDS
RND
PGM
EQ
PRG
SRDE.
PL
DDTS
W1 W2
WS
DISC
S.SRD
TG
KARA
D.MIX
MONO
SLP
0044En_p26-40.fm Page 27 Tuesday, November 28, 2006 3:32 PM