Filter
Top Products
Reference
23
Operations
Troubleshooting
Before requesting service, make the following
checks. If you are in doubt about some of the check
points, or if the solutions indicated in the following
guide do not solve the problem, consult your dealer
for instructions.
No power.
≥ Insert the AC mains lead securely. (> 19)
≥ After turning this unit on, if the indicators blink
and this unit immediately turns off, unplug the AC
mains lead and consult your dealer.
The remote control does not work properly.
≥ The battery is depleted. Replace it with a new
one. (> 8)
≥ It is possible that the insulation sheet has not
been removed. Remove the insulation sheet.
(> 8)
≥ It may be necessary to set the code of the remote
control again after changing the battery of the
remote control. (> 25)
The “TV” indicator blinks, but there is no sound.
Remove the AC mains lead cord and consult your
dealer. If there are any other indicators blinking, be
sure to inform the blinking indicators to your dealer.
The , DTS, PCM indicators blink for 10 sec
and then turn off.
≥ Are you changing the playback mode settings?
(> 21)
≥ Are you changing the 3D sound settings? (> 21)
≥ Are you changing the audio output settings?
(> 24)
Power of this unit is turned off when the input
for the TV is changed.
This is a normal feature when using VIERA Link
(HDAVI Control 4 or later). For details please read
the Operating Instructions for the TV.
This unit does not operate correctly.
If the HDMI cable is connected to the wrong
terminal (HDMI AV IN or HDMI AV OUT), this unit
will not operate correctly. Turn this unit off,
disconnect the AC mains lead and reconnect the
HDMI cable(s). (> 16, 17)
VIERA Link related operations no longer
function properly.
≥ Check the “VIERA Link” setting on the connected
devices.
≥ Have you turned the VIERA Link settings off?
≥ When the HDMI connections are changed, after a
power failure or after the AC mains lead has been
removed, VIERA Link operations may not
function properly.
jTurn on all the devices that are connected to
the TV with an HDMI cable and then turn the
TV on.
jTurn off the VIERA Link settings and turn it on
again. For details refer to the Operating
Instructions for the TV.
jWhile this unit and the TV are connected with
the HDMI cable, turn on the TV and then
remove this unit’s AC mains lead cord and
reconnect it again.
The first few seconds of audio cannot be heard
when using the HDMI connection.
This may occur during DVD-Video chapter
playback. Change the digital audio output setting
on the connected device from “Bitstream” to “PCM”.
If operations become unstable when
connected to a non-Panasonic HDMI
compatible device, connect using an optical
digital audio cable. (> 16)
Turn VIERA Link off.
1 Press and hold [MUTE] on the remote control
and [VOLUME s] on this unit for more than 2
sec.
≥ The setting is changed when the , DTS
and PCM indicators blink.
2 After the setting has changed, turn off and
then on all the connected devices.
≥ To reset the setting, return to the factory preset.
(> left)
≥ When VIERA Link is turned off the ARC function
is not available. Be sure to connect the optical
digital audio cable. (> 16)
To return to the factory preset.
While this unit is on, press [Í/I] on this unit for
more than 4 sec.
(All the indicators will blink twice when the unit is
reset.)
If this unit does not operate as expected,
return the settings to the factory preset.
General operation
D
HDMI
D
SC-HTB520EGEBGNGS_RQTX1279-B.book Page 23 Tuesday, February 22, 2011 9:05 AM