Filter
Top Products
16
RQT6847
Change this setting to listen to content recorded with Dolby Digital at low
volume (such as late at night) and maintain audio clarity. It reduces the
peak level in loud scenes without affecting the sound field.
OFF:The software is played with the original dynamic range (factory
setting).
STANDARD: The level recommended by the producer of the software
for household viewing.
MAX:The maximum allowable compression (recommended for night
viewing).
11
Press [SFC MODE < and >] at the same time to enter
the setting mode.
22
Press [SFC MODE <] to select “DR COMP”.
33
Turn [INPUT SELECTOR] to select “OFF”, “STANDARD”
or “MAX”.
44
Press [SFC MODE < and >] at the same time to exit the
setting mode.
The factory setting is OFF (normal brightness).
Dim the unit’s display for better viewing in a darkened room
11
Press [SFC MODE < and >] at the same time to enter
the setting mode.
22
Press [SFC MODE <] to select “DIMMER”.
33
Turn [INPUT SELECTOR] to select “OFF” or “ON”.
44
Press [SFC MODE < and >] at the same time to exit the
setting mode.
Other settings
DR COMP –
Dynamic range compression
DIMMER
POWER
SFC MODE
8
INPUT SELECTOR
VOLUME
DOWN UP
SPEAKERS
PHONES
VCR 2
VIDEO IN
L AUDIO IN R
DSP
SOUND MODE
DOLBY
PRO LOGIC2
-HE LP
–RESET
-BAND
–FM MODE
MEMORYPRESET
2
TUNING
1
DVD 6CH INPUT
TAPE MONITOR
+
–
LR
SUB WOOFER
BASS/TREBLE
BALANCE
DIGITAL INPUT
INPUT SELECTOR
SFC MODE
<>
You can record to a tape deck connected to TAPE REC (OUT) or to a
VCR connected to VCR 1 OUT.
See the recording unit’s operating instructions for details on how to
prepare it for recording.
When recording with a tape deck, you can record any source except
TAPE.
When recording with a VCR (connected VCR 1), you can record any
source except TAPE or VCR 1.
11
Turn [INPUT SELECTOR] to select the source to be
recorded.
22
Begin recording.
Follow your recording unit’s operating instructions.
33
Start the source to be recorded.
Follow your equipment’s operating instructions.
¡ You cannot record a source connected through a digital terminal.
When recording CD, DVD, or TV, ensure the source is connected
through the corresponding analog terminals and “ANALOG” input is
selected.
¡ When you select DVD 6CH INPUT mode, only sound from the front
left and right channels is recorded.
Note
Recording on a tape deck or VCR
Making a recording
POWER
SFC MODE
8
INPUT SELECTOR
VOLUME
DOWN UP
SPEAKERS
PHONES
VCR 2
VIDEO IN
L AUDIO IN R
DSP
SOUND MODE
DOLBY
PRO LOGIC2
-HE LP
–RESET
-BAND
–FM MODE
MEMORYPRESET
2
TUNING
1
DVD 6CH INPUT
TAPE MONITOR
+
–
LR
SUB WOOFER
BASS/TREBLE
BALANCE
DIGITAL INPUT
INPUT SELECTOR
L
R
L
R
LOOP ANT
HOLDER
FM
ANT
AM
ANT
GND
LOOP
EXT
75
Ω
DIGITAL IN
TAPE
S-VIDEO
TV
OPTICAL1
(TV)
REC
(OUT)
PLAY
(IN)
OPTICAL2
(DVD)
MONITOR
OUT
TV
CD
MONITOR
OUT
CENTER
SURROUND
SUBWOOFER
L
R
TV
IN
VCR
VCR
DVD/DVD 6CH
SUBWOOFER
IN
IN
IN
IN
IN
FRONT
OUT
OUT
DVD
IN
COAXIAL
TV
5–12 m
FM outdoor antenna
¡ Disconnect the FM indoor antenna.
¡ The antenna should be installed by a
competent technician.
¡ Twist the coaxial cable’s shield braid firmly and
connect it to the GND terminal
.
AM outdoor antenna
¡ Run a piece of vinyl wire horizontally across a
window or other convenient location.
¡ Leave the loop antenna connected.
¡ Disconnect the antenna when the unit is not in
use. Do not use the antenna during an electrical
storm.
10 mm (3/8")
20 mm (25/32")
Shield braid
Core wire
FM outdoor antenna
75 Ω coaxial cable
Using outdoor antennas
Vinyl-covered wire
(16–40 ft)
AM loop antenna
(included)
Others