Filter
Top Products
Advanced Operations
En-73
Operating
procedure
(➔ page 60)
You can assign a default listening mode to each input
source that will be selected automatically when you
select each input source. For example, you can set
the default listening mode to be used with Dolby
Digital input signals. You can select other listening
modes during playback, but the mode specified here
will be resumed once the AV receiver has been set to
standby.
■ Analog/PCM/Digital
With this setting, you can specify the listening mode
used when an analog (CD, TV, LD, VHS, MD,
turntable, radio, cassette, cable, satellite, etc.) or
PCM digital (CD, DVD, etc.) audio signal is played.
Note
• For the “GAME2” input selector, only “PCM” is available.
■ Mono/Multiplex Source
With this setting, you can specify the listening mode
used when a mono digital audio signal is played
(DVD, etc.).
■ 2ch Source
With this setting, you can specify the listening mode
used when 2-channel (2/0) stereo digital sources,
such as Dolby Digital or DTS, are played.
■ Dolby D/Dolby D Plus/TrueHD
With this setting, you can specify the listening mode
used when Dolby Digital or Dolby Digital Plus format
digital audio signals are played (DVD, etc.). Specifies
the default listening mode for Dolby TrueHD sources,
such as Blu-ray or HD DVD (input via HDMI).
■ DTS/DTS-ES/DTS-HD
With this setting, you can specify the listening mode
used when DTS or DTS-HD High Resolution format
digital audio signals are played (DVD, LD, CD, etc.).
Specifies the default listening mode for DTS-HD
Master Audio sources, such as Blu-ray or HD DVD
(input via HDMI).
■ Other Multich Source
Specifies the default listening mode for multichannel
PCM sources from HDMI IN such as DVD-Audio, and
DSD multichannel sources such as Super Audio CD.
Volume Setup
■ Volume Display
`Absolute
:
Displayed range is Min, 0.5 to 99.5, Max.
`Relative (THX):
Displayed range is – dB, –81.5dB to +18.0dB.
With this setting, you can choose how the volume level
is displayed.
The absolute value 82 is equivalent to the relative
value 0 dB.
Note
• If the absolute value is set to 82, “82.0Ref” will appear on
the display and the THX indicator will flash.
■ Muting Level
`–
dB (fully muted), –50dB to –10dB in 10 dB
steps.
This setting determines how much the output is muted
when the muting function is used (➔ page 53).
■ Maximum Volume
`Off
, 50 to 99 (Absolute display)
`Off
, –32dB to +17dB (Relative display)
With this setting, you can limit the maximum volume.
To disable this setting, select “Off”.
■ Power On Volume
`Last
, Min, 1 to 99 or Max (Absolute display)
`Last
, – dB, –81dB to +18dB (Relative display)
With this preference, you can specify the volume
setting to be used each time the AV receiver is turned
on.
To use the same volume level that was used when
the AV receiver was turned off, select “Last”.
The “Power On Volume” setting cannot be set higher
than the “Maximum Volume” setting.
5. Listening Mode Preset
1
Use / to select the input source that you
want to set, and then press ENTER.
The following menu appears.
2
Use / to select the signal format that you
want to set, and then use / to select a
listening mode.
Only listening modes that can be used with each
input signal format can be selected (➔ pages 44
to 51).
The “Last Valid” option means that the listening
mode selected last will be used.
The “Straight Decode” option means that
straight decoding listening mode (Dolby Digital,
DTS, etc.) is selected.
Note
• For the “TUNER” input selector, only “Analog” will be
available.
• For the “NET” or “USB” input selector, “Digital” and
“TrueHD” will be available.
Default listening mode for analog and PCM sources.
Analog/PCM
Mono/Multiplex Source
2ch Source
Dolby D/Dolby D Plus/TrueHD
DTS/DTS-ES/DTS-HD
Other Multich Source
Last Valid
5-1. Listening Mode Preset
BD/DVD
Last Valid
Last Valid
Last Valid
Last Valid
Last Valid
• For the “BLUETOOTH” input selector, only “Digital”
is available.
6. Miscellaneous