Filter
Top Products
Advanced Operations
En-67
Operating
procedure
(➔ page 56)
■ Film Mode
*2*4
`Video:
“Film Mode” detection is not applied and the
input signal is handled as a video source.
`Auto:
Detects whether the input signal is a video or a
movie. If it is a movie, the appropriate
conversion is applied.
The AV receiver will adjust to the picture source,
automatically converting it to the appropriate
progressive signal and reproducing the natural quality
of the original picture.
■ Edge Enhancement
*2*4*5
`Off
`Low
`Mid
`High
With this setting, you can make the picture appear
sharper.
■ Noise Reduction
*2*4*5
`Off
`Low
`Mid
`High
With this setting, you can reduce noise appearing on
the screen. Select the desired level.
■ Brightness
*1*2*4
`–50 to 0 to +50
With this setting, you can adjust the picture
brightness. “–50” is the darkest. “+50” is the brightest.
■ Contrast
*1*2*4
`–50 to 0 to +50
With this setting, you can adjust contrast. “–50” is the
least. “+50” is the greatest.
■ Hue
*1*2*4
`–50 to 0 to +50
With this setting, you can adjust the color hue
between “–50” and “+50”.
■ Saturation
*1*2*4
`–50 to 0 to +50
With this setting, you can adjust saturation. “–50” is
the weakest color. “+50” is the strongest color.
■ Color Temperature
*2*4
`Warm
`Normal
`Cool
With this setting, you can adjust the color
temperature.
Note
•“Picture Adjust”
cannot be used when:
–The NET, USB or BLUETOOTH input selector is
selected, or
–“Monitor Out” is set to “Sub”.
*1
This procedure can also be performed on the remote
controller by using the Quick Setup (➔ page 52).
*2
When the “Picture Mode” setting is set to anything other
than “Custom”, this setting cannot be used.
*3
If the “Resolution” setting is set to “4K” (➔ page 57),
this setting is fixed at “Off”.
*4
Press CLR if you want to reset to the default value.
*5
If the “Game Mode” setting is set to “On”, this setting is
fixed at “Off”.
*6
When a 3D video source is input, “Wide Mode” is fixed to
“Full”.
Audio Selector
■ Audio Selector
`ARC:
The audio signal from your TV tuner can be sent
to HDMI OUT MAIN of the AV receiver.
*1
With this selection, the TV’s audio can be
automatically selected as a priority among other
assignments.
`HDMI:
This can be selected when HDMI IN has been
assigned as an input source. If both HDMI
(HDMI IN) and digital audio inputs (COAXIAL IN
or OPTICAL IN) have been assigned, HDMI
input is automatically selected as a priority.
`COAXIAL:
This can be selected when COAXIAL IN has
been assigned as an input source. If both
coaxial and HDMI inputs have been assigned,
coaxial input is automatically selected as a
priority.
`OPTICAL:
This can be selected when OPTICAL IN has
been assigned as an input source. If both optical
and HDMI inputs have been assigned, optical
input is automatically selected as a priority.
`Analog:
The AV receiver always outputs analog signals.
You can set priorities of audio output when there are
both digital and analog inputs.
Note
• This setting can be made only for an input source that is
assigned to HDMI IN, COAXIAL IN, or OPTICAL IN.
• This setting cannot be used with the NET, USB and
BLUETOOTH input selectors.
• When using the Whole House Mode, “Audio Selector” is
fixed to “Analog”.
*1
You can select “ARC” if you select the TV/CD input
selector. But you cannot if you’ve selected “Off” in the
“Audio Return Channel” setting (➔ page 71).