Filter
Top Products
115
Listening Mode Setup
—Continued
• When the settings for “(Speaker A) Surr Back” and
“(Speaker B) Surr Back” in the Speaker Configuration
sub-menu differ, the available options will be “A” and
“B.”
A (Default):
Outputs the source from the speakers connected
to the SURR BACK L/R SPEAKERS A terminals.
B:
Outputs the source from the speakers connected to
the SURR BACK L/R SPEAKERS B terminals.
A+B:
Outputs the source from the speakers connected
to the SURR BACK L/R SPEAKERS A and SURR
BACK L/R SPEAKERS B terminals.
h. Subwoofer
This option configures the subwoofer to use when
playing the source. Select the terminal to which the
subwoofer you want to use is connected. This setting
can be made when the “(Speaker A) Subwoofer” is set
to an option other than “Not Used” in the Speaker
Configuration sub-menu. However, when the “(Speaker
B) Subwoofer” is set to an option other than “Main A”
in the Speaker Configuration sub-menu, the available
options will be “A” or “Not Used.”
A (Default):
Outputs the source only from the
subwoofer connected to the SUBWOOFER PRE OUT
A terminal.
B:
Outputs the source only from the subwoofer
connected to the SUBWOOFER PRE OUT B terminal.
A+B:
Outputs the source from the subwoofers
connected to the SUBWOOFER PRE OUT A and
SUBWOOFER PRE OUT B terminals.
Not Used:
No subwoofers are used for playback.
This sub-menu allows you to configure the audio effect
and playback options when you play a source in the All
Ch Stereo or Full Mono listening modes. The settings in
this sub-menu can be made when the (Speaker A)
Center setting is set to an option other than “Not Used”
in the Speaker Configuration sub-menu.
a. Re-EQ/Academy
This option allows you to configure whether the Re-EQ
or Academy effect is applied or not in the Onkyo
original listening mode. Use these effects when you do
not want to overemphasize the treble sound.
Off (Default):
The effects are not applied.
Re-EQ On:
Adjusts the soundtrack in which the treble
is overemphasized, so that the sound is optimized for
home theater.
Academy On:
Lowers the treble level and filters the
noise when the source contains emphasized treble
sound and too much hiss, such as an old mono audio
movie recorded onto videotape.
b. Front Speaker
This option configures the front speakers to use when
playing the source. Select the speaker terminals to which
the speakers you want to use are connected. This setting
can be made when the “(Speaker B) Front L/R” is set to
“Main A” in the Speaker Configuration sub-menu.
• When the impedance setting for “Front L/R A” or
“Front L/R B” in the Speaker Impedance sub-menu is
set to “6 ohms” or “4 ohms,” the available options will
be “A” and “B.”
A (Default):
Outputs the source from the speakers
connected to the FRONT L/R SPEAKERS A terminals.
B:
Outputs the source from the speakers connected to
the FRONT L/R SPEAKERS B terminals.
A+B:
Outputs the source from the speakers connected
to the FRONT L/R SPEAKERS A and FRONT L/R
SPEAKERS B terminals. Note that this option is not
available when the front speakers are in Bi-amp or in
BTL configuration.
c. Center Speaker
This option configures the center speaker to use when
playing the source. Select the speaker terminal to which
the speaker you want to use is connected. This setting
can be made when the “(Speaker B) Center” is set to
“Main A” in the Speaker Configuration sub-menu.
• When the impedance setting for “Center A” or
“Center B” in the Speaker Impedance sub-menu is set
to “6 ohms” or “4 ohms,” the available options will be
“A” and “B.”
A (Default):
Outputs the source from the speaker
connected to the CENTER SPEAKERS A terminal.
B:
Outputs the source from the speaker connected to the
CENTER SPEAKERS B terminal.
A+B:
Outputs the source from the speakers connected
to the CENTER SPEAKERS A and CENTER
SPEAKERS B terminals.
d. Surr L/R Sp
This option configures the surround speakers to use
when playing the source. Select the speaker terminals to
which the speakers you want to use are connected. This
setting can be made when the “(Speaker B) Surr L/R” is
set to “Main A” in the Speaker Configuration sub-menu.
• When the impedance setting for “Surr L/R A” or “Surr
L/R B” in the Speaker Impedance sub-menu is set to
“6 ohms” or “4 ohms,” the available options will be
“A” and “B.”
A (Default):
Outputs the source from the speakers
connected to the SURR L/R SPEAKERS A terminals.
B:
Outputs the source from the speakers connected to
the SURR L/R SPEAKERS B terminals.
A+B:
Outputs the source from the speakers connected
to the SURR L/R SPEAKERS A and SURR L/R
SPEAKERS B terminals.
All Ch Stereo Setup/Full Mono Setup
Sub-menu