Filter
Top Products
15
Connecting a subwoofer
Use the PRE OUT SUBWOOFER jack to connect a subwoofer with
a built-in power amplifier. If your subwoofer does not have a built-in
amplifier, connect an amplifier to the PRE OUT SUBWOOFER jack
and the subwoofer to the amplifier.
Connecting the speaker cable
1. Strip away 5/8 inch (15 mm) of wire insulation.
2. Twist wire ends very tight.
3. Unscrew
4. Insert wire
5. Screw
Connecting speakers
15mm
(5/8")
12345
FM
75
AM
ANTENNA
REMOTE
CONTROL
MONITOR
OUT
DVD
VIDEO
3
VIDEO
2
VIDEO
1
IN
OUT
IN
IN
IN
VIDEO
S
VIDEO
L
R
OUT
IN
TAPE
PHONO
CD
L
R
GND
CENTER
SUB
WOOFER
FRONT
SURR
SUBWOOFER
PRE OUT
MULTI
CHANNEL INPUT
L
R
OPTICAL
COAXIAL
1
2
12
DIGITAL
INPUT
AV RECEIVER
MODEL NO.
TX-DS595
FRONT
SPEAKERS
B
CAUTION
:
SEE INSTRUCTION MANUAL
FOR CORRECT SETTING.
R
L
6 OHMS
MIN.
/
SPEAKER
4 OHMS
MIN.
/
SPEAKER
IMPEDANCE SELECTOR
AC OUTLETS
SURROUND
SPEAKERS
FRONT
SPEAKERS
A
CENTER
SPEAKER
R
L
SET BEFORE POWER ON
AC 230-240
V 50
Hz
SWITCHED
TOTAL 100W MAX.
R
L
R
L
Center
speaker
Front left
speaker A
Front right
speaker A
Surround
left
speaker
Surround
right
speaker
Subwoofer
Front left
speaker B
Front right
speaker B
NO!
Connecting speakers
1. Check the impedance of the speakers you are
connecting.
The TX-DS595 requires speakers with an impedance of 4 Ω or
greater. Connecting speakers with an impedance of less than 4 Ω
may damage the TX-DS595.
2. Set the IMPEDANCE SELECTOR switch according to
the impedance of the speakers being connected.
If all speakers have an impedance of 6 Ω or greater, slide the
IMPEDANCE SELECTOR switch to the left (6 OHMS MIN./
SPEAKER). If one or more speakers have an impedance of less
than 6 Ω, slide the IMPEDANCE SELECTOR switch to the
right (4 OHMS MIN./SPEAKER).
• When you are using only one
speaker or when you wish to
listen to monaural (mono)
sound, a single speaker should
never be connected in parallel to
both the right and left-channel
terminals simultaneously.
• To prevent damage to circuitry,
never short-circuit the positive
(+) and negative (–) speaker
wire.
Notes:
• The power to the TX-DS595 must not be turned on when
changing the IMPEDANCE SELECTOR setting.
6 OHMS
MIN.
/
SPEAKER
4 OHMS
MIN.
/
SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
6 OHMS
MIN.
/
SPEAKER
4 OHMS
MIN.
/
SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
4 Ω or above/speaker 6 Ω or above/speaker
NO!
+ ––++––+
RL RL
• Be sure to connect the positive and negative cables for the
speakers properly. If they are mixed up, the left and right signals
will be reversed and the audio will sound unnatural.
• Do not connect more than one speaker cable to one speaker
terminal. Doing so may damage the TX-DS595.
• Use FRONT SPEAKERS B terminals to connect a second pair
of front speakers.
• When you listen to surround audio or select Multichannel, be
sure to turn on SPEAKERS A.