Filter
Top Products
16
Selecting a sound source
PO
W
E
R
S
LE
E
P
D
IM
M
ER
S
U
R
M
O
D
E
V
ID
E
O
-1
V
ID
E
O
-2
T
AP
E
D
VD
C
D
C
D
D
V
D
T
U
N
E
R
T
U
N
E
R
P
H
O
N
O
IN
P
U
T
S
ELE
C
TO
R
D
ISC
TA
P
E
V
O
LU
M
E
LE
V
E
L
C
H
S
E
L
P
R
E
S
ET
M
U
TIN
G
T
E
S
T
T
O
N
E
MULTI-CH
INPUT
R
E
M
O
TE
C
O
N
TR
O
LL
E
R
G
R
O
U
P
R
C
-3
85
S
TX-DS474
T
R
E
B
L
E
B
A
S
S
P
H
O
N
E
S
MASTER VOLUME
O
F
F
O
N
P
O
W
E
R
STANDBY/ON
C
D
A
M
P
H
O
N
O
F
M
D
VD
1
V
ID
EO
2
V
ID
E
O
T
I C
H
I
N
P
U
T
M
U
L
TA
P
E
( )
M
O
N
ITO
R
D
IM
M
E
R
S
TA
ND
BY
P
A
R
A
M
E
T
E
R
C
O
N
T
R
O
L
L
E
R
P
A
R
A
M
E
T
E
R
S
E
L
E
C
T
O
R
T
U
N
IN
G
CL
EA
R
M
E
M
O
RY
F
M
M
U
T
E
/
M
O
D
E
S
P
E
A
K
E
R
S
A
B
M
ID
N
IG
H
T
T
H
E
A
T
E
R
S
U
R
R
O
U
N
D
M
O
D
E
S
C
A
N
G
R
O
U
P
P
R
E
S
E
T
1. Press the desired input selector button
or MULTI-CH INPUT button.
The selected source name appears on the
display. Refer to page 17 for more
information on MULTI CH INPUT.
2. Make sure that the SPEAKERS A
indicator is lit on the display. If it is not lit,
press the SPEAKERS A button.
(Refer to the “Speakers selector” section on
the page 18 for more details.)
3. Start playing the selected input source.
Follow the operating instructions for the
source device.
4. Adjust the volume to an appropriate level.
These controls allow you to adjust the volume of the
Front, Center, Surround speakers and subwoofer
simultaneously. Turning the control clockwise
increases the volume level. Turning the control
counter-clockwise decreases the volume level.
DIMMER button
Use this button to change
the brightness of the
display (normal or dim).
4. VOLUME button
(πup/†down)
Use this button to adjust
the volume level.
1. INPUT SELECTOR button
Use this button to select a desired sound source.
DIMMER button
Use this button to change the
brightness of the display (normal
or dim).
SLEEP button
This button allows you to set
the sleep timer.
(Refer to page 19 for more
details.)
MUTING button
This button mutes the sound temporarily.
(Refer to page 19 for more details.)
5. Use the bass, treble
controls to adjust the tone.
(Refer to page 18 for more
details.)
Follow the steps below to select a device to play the sound source.
Note:
If you hear no sound from the speakers, check the following items:
• Make sure that all devices and speakers are connected correctly and securely.
• Make sure that the TAPE MONITOR indicator is not lit on the display when you select an input source other than TAPE. If the indicator is
lit, no sound will be produced. Press the TAPE (MONITOR) button to turn it off and press the desired input selector button.
• The sound is muted when the MUTING indicator is lit. Press the MUTING button on the remote controller to cancel the mute function.
• Refer to page 24 for more information on how to use TAPE MONITOR for recording.
• When you select a source that is connected to the DIGITAL INPUT jacks on the rear panel, you must select digital input (refer to
page 17.).
• If you have selected MULTI CH INPUT, you need to adjust the level of each speaker (refer to page 17).