Filter
Top Products
Installation: New Construction (unfinished ceilings)
1. Once you’ve selected the desired location for the speaker, begin by installing
the mounting bracket between adjacent ceiling joists. First attach the mounting
wings to the bracket by inserting them into the locking plastic tabs in the side of
the bracket (fig.1).
2. The wings feature progressively elongated sections (1”, 1”, 2”, 2”, 2”, 3”, 3”)
with screw holes spaced in one-inch increments. Attach the wings to the joists
with the 5 x 50mm flathead screws. For maximum stability, use two screws for
each wing. Break off the extra portion of the wing by snapping it at one of the
pre-molded “break” lines (fig.2).
3. Complete the pre-wiring before the drywall goes up (see “Tech Tips: Pre-
Wiring for New Construction”). Leave an extra few feet of speaker cable, and
tie it to the the mounting bracket for later.
4. During the drywall phase, cut a hole 8-13/16” around the bracket so that the
drywall surrounds the protruding lip of the mounting bracket. Once installed, the bezel outer frame will extrude out about
1/2 inch beyond the perimeter of the cutout to hide minor imperfections in the cutout (fig.3).
5. After the drywall is complete, connect the speaker cable to the spring clips (CS-6.1 Ci) or spring posts (CS-6.3 Ci) on
the back of the bezel, making sure to observe correct polarity (see “Connections”).
6. The bezel (with driver) attaches to the bracket via four plastic mounting clamps on the back of the bezel that swivel to
“sandwich” the drywall between the bezel frame and the clamps (fig.4). First rotate the mounting clamps counterclockwise
so that the body of the bezel can slide through the mounting bracket. Exercise caution not to damage the driver.
7. Holding the bezel in one hand, rotate the mounting clamps via the four Philips-head screws surrounding the driver on
the front of the bezel (fig.5). Tighten screws snugly, making sure not to over-tighten, as this may compromise the fit of the
bezel. The use of power screwdrivers is not recommended. The absorptive strip on the drywall side of the bezel frame
reduces unwanted vibrations against the drywall and will compress slightly to allow the bezel frame to rest flush against
the wall.
8. If the bezel frame and grille are to be painted in the ceiling, install the paint shield to protect the dri-
ver from overspray (see “Painting”). Once painting is complete, remove the paint shield and set it
aside for use in Step #9.
9a. (CS-6.1 Ci only) The CS-6.1 Ci uses two absorptive foam pads on the inside of the grille to con-
trol sound radiation (fig.6). There are two circular sections in the center of the paint shield that serve
as templates for attaching them. Punch out the larger circle, and the smaller circle from within it. Place
the paint shield (minus the circular sections) on the inside of the metal grille and attach the larger
absorptive pad onto the grille through the circular cutout. Then attach the smaller absorptive pad on
top of the larger pad, using the larger cutout circle as a template. When attached correctly, the two
pads resemble a stepped cone.
9b. (CS-6.3 Ci only) The CS-6.3 Ci uses one absorptive foam pad on the inside of the grille to con-
trol sound radiation (fig.6). There are two circular sections in the center of the paint shield that serve
as templates for attaching it. Punch out the larger circle (not the smaller circle within it). Place the
paint shield (minus the circular section) on the inside of the metal grille and attach the larger absorp-
tive pad onto the grille through the circular cutout. Do not attach the smaller absorptive pad.
10. Attach the metal grille by inserting it into the grooves in the bezel.
fig.3
fig.4 fig.5
fig.6