Mission MS-8 Speaker User Manual


 
Specifications
The power cord on your subwoofer may be supplied with a plug incorporating a
fuse, the value of which is indicated on the pin face of the plug. Should the fuse
need to be replaced, an ASTA or BSI approved BS1362 fuse must be used of the
same rating. If the plug is cut off it must NOT be re-used. Dispose of any such
plug safely. There is a danger of electric shock if a cut-off plug is inserted into a
mains socket.
The wires in the mains lead are coloured in accordance with the following code:
Green and Yellow - Earth: Blue - Neutral: Brown - Live.
As the colours of the wires in the mains lead may not correspond with the
markings identifying the terminals in the replacement mains plug, proceed as
follows:
The wire coloured Blue must be connected to the
terminal marked with the letter ‘N’ or coloured Black.
The wire coloured Brown must be connected to the
terminal marked with the letter ‘L’ or coloured Red.
The wire coloured Green and Yellow must be
connected to the terminal marked with the letter ‘E’,or
coloured Green, or Green and Yellow, or marked with
the Earth symbol
MS-DUO; MS-10: MS-CUBE:
MS-8:
The wire coloured Blue must be connected to the
terminal marked with the letter ‘N’ or coloured Black.
The wire coloured Brown must be connected to the
terminal marked with the letter ‘L’ or coloured Red
LIVE
(BROWN)
NEUTRAL
(BLUE)
EARTH (GREEN/YELLOW)
FUSE
Note for UK Customers
11
MS-8 MS-10
Recommended Amplifier:
Enclosure:
Effective Volume:
Frequency Response
Filter Selection
Bass Unit
Net Weight
Dimensions
Height on Feet
Integrated 100W
amplifier
reflex
20 litres 35 litres
: 38 Hz - 120 Hz
35Hz-85Hz 40Hz - 200Hz
(10 Hz steps) (variable)
250mm
11.0 kg
(HxWxD):mm 300x 300 x330 410x280x500 38 345 37 38 330 355
mm 330 410 38
MS-CUBE MS-DUO
Integrated 150W Integrated 200W Integrated 150W
amplifier amplifier amplifier
reflex reflex reflex
30 litres 30 litres
30 Hz - 165 Hz 35 Hz - 110 Hz 35 Hz - 110 Hz
35Hz-85Hz 35Hz-85Hz
(10 Hz steps) (10 Hz steps)
250mm 250mm 250mm
18.6 kg 15.0 kg 15.2 kg
0x x 0 0x x
0 380
Class II Class I1 Class I Class I
Do not Earth. Requires Earth Requires Earth Requires Earth
Electrical Class
Mission reserves the right to change all specifications without notice.E&OE
LIVE
(BROWN)
NEUTRAL
(BLUE)
FUSE
14
Welcome to Mission
General Information
Unpacking Your Loudspeakers
The series is the latest in a long line of distinguished Mission loudspeakers. These technologically advanced loudspeakers will
complement the finest electronics and décor. ass drivers tweeters are used throughout the range.
binding posts feature on all models. Your Mission loudspeakers will bring you great listening
pleasure for many years.
Mv
Mv
Robust b and precision silk
Screw fastening tri-lobe multi-way
Please read these instructions carefully before installing your loudspeakers. A few minutes studying this manual will ensure
superb performance from your loudspeaker for many years.
Please pay attention to all cautions printed on the pages marked with this symbol.
Carefully unpack each loudspeaker.
Retain all the packing materials so that your loudspeaker can be repacked and shipped without damage.
If you dispose of the packing,do so with regard to all recycling provisions in your area..
Warning: Be careful. Loudspeaker spikes are very sharp.
When positioning the speakers avoid piercing any electrical cables.
The and loudspeakers are supplied with the spike retainers fitted to the plinth but you will need to fit the spikes
Mv-6 Mv-8
Fitting Spikes
Fitting the Spikes
Adjusting the Spikes
Invert the loudspeaker and place the top on a soft stable surface, or place the
loudspeakers on a towel or soft cloth to protect the surface.
Screw a nut fully on to each spike but ensure the nut is not tight.
Place a washer over the spike retainer.
Screw a spike half way into each spike retainer fitted in the base of the cabinet.
Tighten the nut finger tight onto the spike retainer.
Carefully return the loudspeaker to its normal position.
Ensure that spikes do not pierce cables etc. under the carpet.
Loosen each collar slightly.
Adjust the height by screwing in or out one or more of the spikes
until the loudspeaker is stable and level.
Tighten the nut fully tight onto the spike retainer.
Warning:
Never drag a loudspeaker. W lift them clear of the floor and replace them carefully
The and loudspeakers are heavy.
Always get someone to help you to lift and manoeuvre the loudspeakers.
hen moving loudspeakers
Mv-6 Mv-8
3