Filter
Top Products
PAGE 15
Although the term filament and heater are often used interchangeably, there are specific differences: A filament is a directly heated
cathode where cathode coating is applied directly to the heating element. Examples are 5U4 twin diode rectifier and 300B triode
amplifier tubes.
A heater, on the other hand, is a heating element which is separate from the cathode and is usually inserted within the tubular cathode
sleeve. Examples are 12AX7 twin triode amplifier and 6V6 or EL84 beam power pentode tubes. In all cases this fundamental aspect
of each tube’s construction is clearly visible, especially when the heating element is glowing red hot.
The cathode, then, would be considered the first numbered element because it is the source of the electrons. The word itself is from
the Greek literally meaning completely down, which implies a sense of central origin - like the center of the earth where Tone begins.
It might be said that an ecstatic audiophile experiences a positive catharsis, his soul being purified when his system transports him to
Audio Nirvana. The only trouble with taking this positive imagery too far is that the cathode is, unfortunately, negative... at least
electrically speaking. However this is easily remembered since virtually all musicians and audiophiles have also experienced the
more common negative catharsis when they emerge from the emotional rebirth kicking and screaming in rage and frustration.
Once heated, the intrinsically negative electrons are energetic little fellows of almost no mass. Thus they may be accelerated almost
instantaneously and will travel through a vacuum a nearly the speed of light. Being of like, negative charge, they tend to repel one
another and thus within the electron cloud surrounding the cathode, there is much jostling and elbowing as each one tries to maintain
his distance from all the others... unless there is a strong and universal attraction from an outside influence.
Visualize, if you will, a group of sub-atomic Irishmen milling about and in a repellent, negative state of mind. All are scowling and none
wants to have anything to do with the other. Now introduce a strong attraction say, a public bar, and you can easily picture an orderly,
if rapid movement of the lot in a single direction. This is what happens when a positively charged element called the anode or plate is
introduced into the vacuum.
The plate is the large metal element most prominently visible through the glass of an electron tube. It is the outermost element of a
tube’s structure and it surrounds all the others. The cathode is at the center radiating electrons outwards. As higher and higher
positive voltage is applied to the plate, the attraction for the electrons surrounding the cathode is increased and with nothing standing
in the way, full uninhibited flow to the plate occurs... sort of like removing the doors and offering free drinks to the crowd of surly
Irishmen milling around outside.
As electrons flow to the plate, the space charge will continually be replenished by further ‘boiling’ of the hot, electron-rich cathode as
you can easily imagine other Irishmen impatiently taking up the places of those who’ve gone inside - until the entire village is
deserted.
Now, where do they come from and how do they emerge? Well, a grand and elegant lady once showed me how to revive flat
champagne: She dropped a raisin into the glass. There was a dramatic and immediate increase in effervescence with the introduction
of a cathoding surface. Thousands of tiny bubbles suddenly appeared - and continued to flow from the raisin. Of course the bubbles
were made up of gas dissolved in the beverage, but the analogy makes it easy to visualize the loosely bound electrons dissolved in
the rich cathode coating as they effervesce from its heated surface.
But back to the electron flow. If the electrons are strongly attracted to a positively charged plate, then it follows that they are strongly
repelled by a negatively charged plate and they are. Thus, if an alternating current - such as comes from a transformer - is applied to
the plate, electrons will flow only during the times when the plate is positively charged. During periods of negative plate charge,
electron flow is stopped and the space charge of electrons remains compressed in the area around the cathode.
Thus a diode tube - one with a cathode and an anode - is mostly used to rectify alternating current into direct current by passing it
without restriction, but in one direction only. This also explains why closing time is stricly enforced at Irish pubs: During normal
operation, the traffic flow is similarily unimpeded and uni-directional toward the bar and this process rectifies the work-day negativity.
It goes without saying that no one leaves as long as the atmosphere around the bar remains positively charged.
ON TRIODES, PENTODES & IRISHMEN: (Continued)