PAGE 11
REAR PANEL:
FUSE:
This is the A.C.’s (Alternating Current) main fuse and provides protection from outside A .C. fl uctuations as well as power
tube failure damage. Should the
FUSE
blow, replace it with the same rating in a Slo-Blo type package. The domestic U.S. version
requires a 4 amp Slo-Blo
FUSE
. A power tube short or failure is often the cause of a blown
FUSE.
..Follow the cold start procedure
mentioned in the ON/STANDBY switch section and watch the power tubes as you fl ip the STANDBY to the ON position. If a power
tube is going bad or is arcing you will see it! Flip the STANDBY switch to Standby immediately and replace the faulty power tube and
the
FUSE
if necessary.
If you see nothing abnormal as you switch the STANDBY on, it is possible that a power tube shorted tempo-
rarily and blew the
FUSE
. If this is the case it may work again normally. To be safe, you might want to replace
just the adjacent tube or all power tubes in the “shotgun” troubleshooting tradition and save the replaced set
as spares. Spare fuses are a must for the fabled cord bag along with your spare tubes. Always carry both for
they could be worth their weight in gold someday.
RECTIFIER SELECT: Diodes / Tube Rectifi er Tracking
This two position toggle selects the type of rectifi er, Silicon Diodes or
Tube, to convert the voltage from AC to DC for the power supply. The
LONE STAR
incorporates a further improved version of our
patented Switchable Rectifi er feature fi rst seen on the
Dual and Triple Rectifi er SOLO
heads. It incorporates a Rectifi er Tracking™
Dual and Triple Rectifi er SOLO heads. It incorporates a Rectifi er Tracking™ Dual and Triple Rectifi er SOLO
feature that insures proper voltage is present at all times and improves reliability. This switch operates in tandem with the individual
Channel Power Select (50/100) switch located on the right side of the Front Panel.
The Rectifi er Tracking feature monitors the Channels, determines their power status and automatically selects
the proper rectifi er type - which ultimately assures the best sound. This provides optimization of the power
settings, delivering a magical tube-rectifi ed power-sag vibe for the channel set to 50 watts - and a tighter,
bolder 100 watts of diode-rectifi ed authority for the channel set to full power.
Selecting
DIODES
chooses the solid state diode rectifi ers which deliver maximum power and headroom, while tracking tighter and
imparting a quicker transient response and bolder attack. When set to
DIODES
, both Channels will respond with this character
regardless of their individual power settings on the Front Panel. Selecting
TUBE RECTIFIER TRACKING
engages the 5U4 rectifi er
tube automatically (either or both channels) whenever the 50 watt selection is made on the Front Panel Channel Power Select switch.
When switching to the opposite channel, if the Channel Power Select is set to 100 watts, the Diodes are automatically engaged to
insure proper matching to the added load on the supply.
This innovative feature allows you to tune each channel for the ultimate power expression and feel. With this fl exibility you can switch
between a high power, spanking clean rhythm sound in Channel 1- and a saggy brown, old school power clip for bluesy single note
solo work with the DRIVE bypassed in Channel 2. Or conversely, set Channel 1 for a sweet low power clean sound and crank up the
horsepower with the DRIVE active to articulate a high gain solo voice in Channel 2. Regardless of the way you choose to dedicate
your Channels, you will fi nd this power section fl exibility a remarkable step forward toward your ultimate tone.
NOTE:
Don’t forget the Front Panel AC switch incorporates the reduced voltage TWEED setting. This adds yet another dimension to
the power expression scenario and can produce amazing results when combined with the
TUBE RECTIFIER TRACKING
feature. Be
sure to experiment with these two features in combination with each other.
WARNING:
Unplug power
before replacing
fuse or removing
bolts mounting
chassis
POWER FUSE
4 A
SLO
BLO
120 V~
60 Hz
4 A
POWER FUSE
FUSE
FUSE
DIODES
TUBE
RECTIFIER
TRACKING
WARNING:
Unplug power
before replacing
fuse or removing
bolts mounting
chassis
POWER FUSE
4 A
SLO
BLO
120 V~
60 Hz
4 A
POWER FUSE
FUSE
FUSE
DIODES
TUBE
RECTIFIER
TRACKING
WARNING:
Unplug powe
r
before replacing
fuse or removing
bolts mounting
chassis
SLAVE
POWER FUSE
4 A
SLO
BLO
120 V~
60 Hz
4 A
WER FUSE
FUSE
FUSE
SILICON
DIODES
TUBE
RECTIFIER
TRACKING
FA
N
ON
FA
N
OFF
First set sound with
LOOP bypassed. Then
set SEND & OUTPUT
to 50% for unity gain.
With LOOP IN, adjust
SEND to match FX.
Use OUTPUT for
RETURN level and
live volume control.
SEND
RETURN
NORMAL
MIN
SEND LEVEL
TUBE LOCATIONS
1 x 5U4 4 x 6L6
1 x 5U4 4 x 6L6
LOOP
IN
HARD BYPASS
OOGIE
B
M
ESA
LONE STAR
CH 2 REVERB CH 1
REVERB
BRIGHT
REV W
ARM
ALL - TUBE
AMPLIFIER
CHANNEL
SOLO
EXT
SW
SPEAKERS
HAND BUILT IN PETALUMA CA.
8 OHM4 OHM 4 OHM
BIAS SELECT
EL-34
WHEN
RED ON
EL-34
6L6
CAUTION: SWITCH MUST
MATCH TUBES IN USE