Filter
Top Products
11
ENGLISH
PLAYBACK
To explain how to play back input sources, representative
examples are given with an CD player and analog record player.
Before starting either procedure, check the component is
correctly connected to the PM7001.
77
77
7 Disc Playback on an CD Player
1. Press the power ON/OFF button of the CD player to activate
power to it.
2. Press the POWER ON/OFF button q to activate power to
it. Approximately 8 seconds after power has been activated,
the muting turns OFF and audio output is enabled.
3. Select the CD from the INPUT SELECTOR knob e.
4. To use the speakers connected to the SPEAKERS
SYSTEM terminals, press the SPEAKERS button 1 and 2
o.
5. Load a disc into the CD player and press the play button to
start playback.
6. Adjust the volume level from the VOLUME knob u.
7. Adjust bass/treble as desired from the BASS and TREBLE
knobs !1. Be sure to first set the SOURCE DIRECT button
i in the OFF position.
77
77
7 Disc Playback on an Analog
Record Player
1. Press the POWER ON/OFF switch q to activate power to
it. Approximately 8 seconds after power has been activated,
the muting turns OFF and audio output is enabled.
2. Select “PHONO” as the input source from the INPUT
SELECTOR knob e. To prevent unexpected accidents, it
is recommended to set the volume level to MIN. by turning
the VOLUME knob u until muting the volume level.
3. MM type cartridges can be connected. Use a step-up
transformer when using an MC cartridge.
4. To use the speakers connected to the SPEAKERS
SYSTEM terminals, press the SPEAKERS button 1 and 2
o.
5. Set a record on the analog record player and play it.
6. Adjust the volume level from the VOLUME knob u.
7. Adjust bass/treble as desired from the BASS and TREBLE
knobs !1. Be sure to first set the SOURCE DIRECT button
i in the OFF position.
BASIC OPERATION
RECORDING
This example explains how to record from an input source
such as an CD player to a recording device such as a CD-R.
1. Press the power ON/OFF switch of the CD player and CD-
R to activate power to both components.
2. Press the POWER ON/OFF switch q to activate power to
it. Approximately 8 seconds after power has been activated,
the muting turns OFF and audio output is enabled.
3. Select the CD with the REC SELECTOR knob !2. If you
want to listen to the recording source through the speakers,
set the INPUT SELECTOR knob e to the CD position.
4. Load a playback disc into the CD player and a recording
disc into the CD-R.
5. Start playback on the CD player. Then, start recording on
the CD-R.
About the REC SELECTOR
The REC SELECTOR knob !2 can be operated independently,
irrespective of the input source selected using the INPUT
SELECTOR knob e.
OFF:
Cannot record because no signal is output to the
RECORDER 1, 2 jacks.
PHONO, CD, TUNER, AUX/DVD:
Selects the program source for recording.
COPY RECORDER 1-2:
Select this to copy the RECORDER 1 signal onto
RECORDER 2.
COPY RECORDER 2-1:
Select this to copy the RECORDER 2 signal onto
RECORDER 1.
MUTEMUTE
RECORDERRECORDER
2211
AUX/DVDAUX/DVDTUNERTUNERPHONOPHONO CDCD
STANDBYSTANDBY
SPEAKERSSPEAKERS
OFFOFF
ONON
INTEGRATED AMPLIFIER PM7001INTEGRATED AMPLIFIER PM7001
TREBLETREBLE BALANCEBALANCE
POWER ON/OFFPOWER ON/OFF
PHONESPHONES
BASSBASS
RECORDER2RECORDER2
INPUT SELECTORINPUT SELECTOR
RRLL
VOLUMEVOLUME
++
--
++
--
1 21 2
2 12 1
RECORDERRECORDER
TUNERTUNER
PHONOPHONO
MAXMAXMINMIN
11
SOURCE DIRECTSOURCE DIRECT
22
COPYCOPY
OFFOFF
REC SELECTORREC SELECTOR
CDCD
AUX/DVDAUX/DVD
ONON
OFFOFF
q e u
i!1 o
MUTEMUTE
RECORDERRECORDER
2211
AUX/DVDAUX/DVDTUNERTUNERPHONOPHONO CDCD
STANDBYSTANDBY
SPEAKERSSPEAKERS
OFFOFF
ONON
INTEGRATED AMPLIFIER PM7001INTEGRATED AMPLIFIER PM7001
TREBLETREBLE BALANCEBALANCE
POWER ON/OFFPOWER ON/OFF
PHONESPHONES
BASSBASS
RECORDER2RECORDER2
INPUT SELECTORINPUT SELECTOR
RRLL
VOLUMEVOLUME
++
--
++
--
1 21 2
2 12 1
RECORDERRECORDER
TUNERTUNER
PHONOPHONO
MAXMAXMINMIN
11
SOURCE DIRECTSOURCE DIRECT
22
COPYCOPY
OFFOFF
REC SELECTORREC SELECTOR
CDCD
AUX/DVDAUX/DVD
ONON
OFFOFF
q e
!2
05.7.20, 3:46 PMPage 11