Filter
Top Products
3
ENGLISH
ENGLISH
ENGLISH
3. FINE, MANUAL TUNING
This function used for selection the manual tuning of the fine tuning
mode.
Fine tuning mode is available only in the FM mode.
1. Press the TUNING MODE button.
2. Every time you press this button, the following will be displayed
FINE ⇔ MANUAL.
a. In FINE (Tuning) mode
When you try press the TUNING 5∞ button, the frequency will be se-
lected by 10 kHz step to ±50 kHz. Then, it will automatically be set to
the MANUAL mode in 4 second.
b. In MANUAL (Tuning) mode
1.
Press the TUNING 5∞ button in the FM band, then the frequency
will be selected by 50 kHz step.
2. In the MW band, the frequency will be selected by 9 kHz step.
3. In the LW band, the frequency will be selected by 1 kHz step.
4. DIRECT TUNING
(The following operation can be performed by connecting the RC-5 BUS
system.)
1. Press the F. DIRECT (frequency direct) button
2. Next press the numeric (0 to9) button.
For example: FM 98.10 MHz
a. FM is chosen with BAND (or TUNER) button on remote controller.
b. Press the F. DIRECT (Frequency Direct) button.
c. Press the numeric button of “9”.
d. Press the numeric button of “8”.
e. Press the numeric button of “1”.
f. Press the numeric button of “0”.
g. The display fixed 98.10 MHz and broadcast station received.
MW, LW band is same as above operations.
5. ADJUSTING CURRENT TIME
You can adjust the current time regardless of power on/standby.
1. Press the TIME ADJ button. Then “Hour display” indicator will blink.
2. The hour is set with the TUNING 5∞ button.
3. Press the NEXT button. Then “minute display” indicator will blink.
4. The minute is set with the TUNING 5∞ button.
5. Press the NEXT button.
OPERATIONS
1. MEMORY PRESETTING
a. Manual operation
For example: presetting FM 90.1 M Hz, to Preset number. 10
1. Select the FM by using the BAND button.
2. Tune to 90.1 MHz by using the TUNING 5∞ button.
3. Press the MEMO button briefly (for less than 0.5 second) Then,
“MEMO” will bricking in the florescent tube display.
4. Select the preset number by using the TUNING 5∞ button.
5. MEMO button pushed again, 90.1 MHz (broadcast station) was able
to be memorized in number 10 by this.
Note:
Be sure to select the antenna A or B memorization when you preset
manual memory in FM broadcast.
b. Automatic operation
1.
Select the desired broadcasting (FM, AM, or LW) by using the BAND
button.
2. Press the MEMO button slightly longer than 1.5 second does.
Then, broadcasting will be automatically received, and as many
broadcasting station are received well will be memorized preset num-
ber-01 after another
3. Check the broadcasting station by using the TUNING 5∞ button.
Note:
1. In the case of FM automatic presetting, the antenna A, B selector
is set to “A” automatically,
And the broadcasting station is scanned twice. The stations that
have stronger broadcasting signal are preset in the first time.;
weaker ones are preset in the second time.
2. If a new broadcasting station is preset into a channel the broad-
casting station which has been preset into that position aria will be
automatically erased.
3. In mountainous or remote area broadcasting stations which have
weak broadcasting signals cannot be automatically preset into the
memory.
4. Max. 30 broadcasting stations each for FM, AM(MW and LW) bands
can be preset.
2. LISTENING TO RADIO
1. Select FM, AM, or LW by using the BAND button.
2. Tune to the desired broadcast by using the TUNING or PRESET
5∞ button.
3. FM broadcasting is set up to “STEREO” mode
If the broadcasting signal is weak, or if there is a large amount of
interference in FM stereo broadcast, change the monaural mode by
presetting the FM MODE button.
4. Select the IF BAND (FM bandwidth)
Select the NARROW bandwidth by pressing this button if the broad-
cast signal is interfered with adjacent broadcast in the FM .
blink
blink
blink