Filter
Top Products
Important safety information
Explanation of symbols used in this manual and on the product:
This symbol is intended to alert the user to the presence, within the
enclosure, of uninsulated dangerous voltages of sufficient magnitude to
cause electric shock.
This symbol is intended to alert the user to the presence of important
maintenance and servicing information in the instruction and service
manuals.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
GENERAL SAFETY INSTRUCTIONS
1. Read instructions. Read the safety and operating instructions before operating
the appliance.
2. Retain instructions. Retain the safety and operating instructions for future
reference.
3. Heed warnings. Observe all warnings on the appliance and in the operating
instructions.
4. Follow instructions. Follow all operating and use instructions.
5. Water and moisture. Do not use the appliance near water, for example near
a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a
swimming pool and the like.
6. Carts and stands. Use only with a cart or stand that is recommended by the
manufacturer.
6a. An appliance and cart combination should be used with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
7. Wall or ceiling mounting. Mount to a wall or ceiling only as recommended by the
manufacturer.
8. Ventilation. Site the appliance so that its location or position
does not interfere with its proper ventilation. For example, the appliance should
not be situated on a bed, sofa, rug, or similar surface that may block the
ventilation openings, or placed in a built-in installation such as a bookcase or
cabinet that may impede the flow of air through the ventilation openings.
9. Heat. Site the appliance away from heat sources such as radiators, heaters,
stoves, or other appliances (including amplifiers) that produce heat.
10. Power sources. Connect the appliance to a power supply only of the type
described in the operating instructions or marked on the appliance.
11. Grounding or polarisation. Do not defeat the safety purpose of the polarised or
grounding type plug. A polarised plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. When the provided
plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
12. Power cord protection. Route power cords so that they are not likely to be
walked on or pinched by items placed upon or against them, paying particular
attention to cords at plugs, power sockets, and at the point where they exit
from the appliance.
13. Protective attachment plug. As a safety feature the product is equipped with an
attachment plug containing overload protection. See the instruction manual
about resetting or replacing the plug. Should the plug need replacing ensure
that a replacement is used which has the same overload
protection as the original.
14. Cleaning. The product should be cleaned only as recommended by the
manufacturer.
15. Power lines. An outdoor antenna should be located away from power lines.
16. Outdoor antenna grounding. If an outdoor antenna is connected to the
tuner/receiver ensure that the antenna system is grounded to provide some
protection against voltage surges and static build up. In the USA see article
810 of the National Electrical Code ANSI/NFPA 70 concerning installation
requirements.
17. Lightning storms. Unplug this apparatus during lightning storms or when unused
for long periods of time.
18. Objects and liquid entry. Do not let objects or liquids fall into the product.
Do not expose the product to dripping or splashing. Do not place a vessel
containing liquid on top of the product.
19. Damage requiring service. The product should be serviced by qualified
personnel if:
a) The power cord or plug has been damaged.
b) Objects or liquid have fallen into the product.
c) The product has been exposed to rain.
d) The product does not appear to operate normally or
exhibits a marked change in operation.
e) The product has been dropped or the enclosure damaged.
20. Servicing. Don’t attempt to service the product beyond that described in the
operating instructions. All other servicing should be referred to qualified service
personnel.
Copyright and Acknowledgements
Copyright © 2003 Linn Products Limited. First edition June 2003.
Linn Products Limited, Floors Road, Waterfoot, Glasgow, G76 0EP, Scotland,
United Kingdom.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior written consent
of the publisher. Linn and the Linn logo are registered trade marks of Linn Products
Limited.
Printed in the United Kingdom.
Linn Part Number: PACK 848.
The information in this manual is furnished for informational use only, is subject to
change without notice, and should not be construed as a commitment by Linn
Products Limited. Linn Products Limited assumes no responsibility or liability for any
errors or inaccuracies that may appear in this manual.
UK USERS PLEASE READ THIS
IMPORTANT SAFETY INFORMATION
Replacing the fuse in the mains plug
This appliance is fitted with a non-rewireable 10 Amp mains plug. The plug contains
a 10 Amp fuse. If the fuse has blown it can be replaced as follows:
a) Pull out the red fuse cover/carrier.
b) Remove and dispose of the blown fuse.
c) Fit a new 10 Amp BS1362 approved fuse into the carrier and push the
carrier back into the plug.
Always ensure the fuse cover is fitted. If the fuse cover is missing do not use the
plug. Contact Linn to obtain a replacement fuse cover. Fuses are for fire protection
and do not protect against electric shock.
Mains plug replacement
Should your mains plug need replacing and you are competent to do this proceed as
follows. If you are in doubt contact your Linn retailer or a competent electrician.
a) Disconnect the plug from the mains supply.
b) Cut off the plug and dispose of it safely. A plug with bared conductors is
dangerous if engaged in a live socket.
c) Only fit a 10 Amp BS1363A approved plug with a 10 Amp fuse.
d) The cable wire colours or a letter will be marked at the connection points of
most quality plugs. Attach the wires securely to their respective points. The
Brown wire must go to the Live pin, the Blue wire must go to the Neutral pin,
and the Green/Yellow wire must go to the Earth pin.
e) Before replacing the plug top ensure that the cable restraint is holding the
outer sheath of the cable firmly and that the wires are correctly connected.
WARNING
THIS APPLIANCE MUST BE EARTHED.
CE Declaration of Conformity
Linn Products Ltd declare that this product is in conformance with the Low Voltage
Directive 73/23/EEC and Electromagnetic Compatibility 89/336/EEC as amended
by 92/31/EEC and 93/68/EEC.
The conformity of the designated product with the provisions of Directive number
73/23/EEC (LVD) is proved by full compliance with the following standards:
Standard number Date of issue Test type
EN60065 1998 General requirements
Marking
Hazardous radiation
Heating under normal conditions
Shock hazards under normal
operating conditions
Insulation requirements
Fault conditions
Mechanical strength
Parts connected to the mains supply
Components
Terminal devices
External flexible cords
Electrical connections and mechanical fixings
Protection against electric shock
Stability and mechanical hazards
Resistance to fire
The conformity of the designated product with the provisions of Directive number
89/336/EEC (EMC) is proved by full compliance with the following standards:
Standard number Date of issue Test type
EN55013 2001 Conducted emissions
EN55013 2001 Absorbed emissions
EN55020 2002 Immunity
FCC Notice
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
English