Filter
Top Products
min max dB dB
-40 0
–+
0
LOW
–+
0
HIGH
TONE CONTROLLEVEL
LINE/CD VOICE OVER MUSIC
LINE
MASTER
VOLUME
BATTERY
STATUS
I
N
O
U
T
MIC 1
MIC 2
min max
min max
LEVEL
LEVEL
LOW CUT
LIMIT
musicspeech
IN
min max
LEVEL
LOW CUT
musicspeech
IN
LOW OK
WIRELESS
MIC 1
LOW CUT
musicspeech
WIRELESS
MIC 2
LOW CUT
musicspeech
ONMUTE
EXTERNAL
SPEAKER A
SWITCHED
8 OHM
EXTERNAL
SPEAKER B
8 OHM
CHARGING STATUS
LightSPEED
MADE IN EUROPE
EXTERNAL
POWER
SOURCE
MAINS
12VDC/4A
AC
90-264V
47-63Hz
FUSE
T2A
POWER
ON
OFF
MUTE
DO NOT OPEN
THE COVER.
REFER SERVICING
TO QUALIFIED
PERSONNEL.
REPLACE FUSE
ONLY WITH
THE SAME TYPE
AND RATING.
ACTIVE
LINK
GND
+ 12V
4
1
2
3
Wireless
Sound System
WIRELESS MIC 1 WIRELESS MIC 2
CD-ROM ART GOES HERE
NO
diSC
STOP PLAY/PAUSEA — BREPEAT
SCAN/SEARCH— SKIP —EJECT
PROG
LightSPEED
7100R
UHF TRUE
DIVERSITY
RECEIVER
AB
LOW
BAT
SCAN SQ
RF
CHANNEL
LightSPEED
7100R
UHF TRUE
DIVERSITY
RECEIVER
AB
LOW
BAT
SCAN SQ
RF
CHANNEL
VOL
MaxPWR Min
VOL
MaxPWR Min
Delta X10
ON MUTE
EXTERNAL
SPEAKER A
SWITCHED
8 OHM
EXTERNAL
SPEAKER B
8 OHM
CHARGING STATUS
LightSPEED
MADE IN EUROPE
EXTERNAL
POWER
SOURCE
MAINS
12VDC/4A
AC
90-264V
47-63Hz
FUSE
T2A
POWER
ON
DO NOT OPEN
THE COVER.
REFER SERVICING
TO QUALIFIED
ACTIVE
LINK
GND
+ 12V
4
1
2
3
2
Volume
LightSPEED
7100R
UHF TRUE
DIVERSITY
RECEIVER
AB
LOW
BAT
SCAN SQ
RF
CHANNEL
VOL
MaxPWR Min
3
Frequency Group
4
5
SCAN
Manual Channel
Select Buttons
1
LightSPEED Technologies • Wireless Sound Solutions • Toll Free: 1-800-840-3662
18
Wireless Receiver(s)
Operating Instructions
LightSPEED
7100R
UHF TRUE
DIVERSITY
RECEIVER
AB
LOW
BAT
SCAN SQ
RF
CHANNEL
VOL
MaxPWR Min
DETDET
DETDET
DET
AILED OPERAAILED OPERA
AILED OPERAAILED OPERA
AILED OPERA
TION - WIRELESS RECEIVERTION - WIRELESS RECEIVER
TION - WIRELESS RECEIVERTION - WIRELESS RECEIVER
TION - WIRELESS RECEIVER
Power up the Delta X system and wireless receiver(s)Power up the Delta X system and wireless receiver(s)
Power up the Delta X system and wireless receiver(s)Power up the Delta X system and wireless receiver(s)
Power up the Delta X system and wireless receiver(s)
1.1.
1.1.
1.
POWER:POWER:
POWER:POWER:
POWER: Push the POWER switch on the base unit back panel to the ON (or MUTE) position.
2.2.
2.2.
2.
ON LED:ON LED:
ON LED:ON LED:
ON LED: The ON LED will light.
3.3.
3.3.
3.
Receiver VReceiver V
Receiver VReceiver V
Receiver V
olume:olume:
olume:olume:
olume: Rotate the Power/Volume knob on the receiver module clockwise to turn on.
Leave the volume at a low
level for now.
4.4.
4.4.
4.
Frequency Group:Frequency Group:
Frequency Group:Frequency Group:
Frequency Group: When the receiver power is first switched on, the frequency group of the receiver will be shown briefly
as letters on the LED display.
(See frequency group chart on page 30)
Channel Selection - Wireless ReceiverChannel Selection - Wireless Receiver
Channel Selection - Wireless ReceiverChannel Selection - Wireless Receiver
Channel Selection - Wireless Receiver
Each receiver has 100 user-selectable channels to choose from. You can select a channel either manually or by pressing the
SCAN button which will automatically select a clear channel.
5.5.
5.5.
5.
Clear Channel Scan (Recommended): Clear Channel Scan (Recommended):
Clear Channel Scan (Recommended): Clear Channel Scan (Recommended):
Clear Channel Scan (Recommended): Make sure the transmitter(s) is OFF before pressing this button. When this button
is pressed, the receiver will cycle through all 100 channels and select a clear frequency (this process takes about 20
seconds). Once the receiver selects the clear channel, you will need to select the same channel on the corresponding
transmitter (handheld or belt-pack).
If YIf Y
If YIf Y
If Y
ou Have a Second Receiver (WIRELESS MIC 2):ou Have a Second Receiver (WIRELESS MIC 2):
ou Have a Second Receiver (WIRELESS MIC 2):ou Have a Second Receiver (WIRELESS MIC 2):
ou Have a Second Receiver (WIRELESS MIC 2): Verify that WIRELESS MIC 1 is operating on a clear channel, and the
transmitter for WIRELESS MIC 1 is turned ON. Make sure the transmitter for WIRELESS MIC 2 is turned OFF, and then press the
“SCAN” button on the WIRELESS MIC 2 receiver. After the WIRELESS MIC 2 receiver selects a clear channel, set the WIRELESS
MIC 2 transmitter (handheld or belt-pack) to the selected channel.