Filter
Top Products
DEVICE/ SOURCE SELECT [ » CD / TUNER / TAPE / AUX « ]
• Press the appropriate button
* to select a device or change the source:
CD = CD player TUNER = radio TAPE = cassette recorder AUX = external device, e.g. record deck
ADJUST VOLUME [ » VOLUME / MUTE « ]
• To increase the volume use the
̆ button W.
• To reduce the volume use the ̄ button Q.
• To mute (silence) the loudspeakers and headphones press the mute button ^.
ADJUST TONE [ » CLASSIC / ROCK / POP « ]
Use the tone selector button
% to set the tone quality of a track to suit the type of music and increase listening pleasure. The
current setting CLASSIC, ROCK or POP is shown in the display
@ - (blank display = neutral tone).
HEADPHONES [ » PHONES « ]
8-32 Ohm stereo headphones
5 can be connected to the headphones connector with a 3.5 mm jack plug. As soon as the headphones
are connected the loudspeakers are turned off. Please note that high levels of sound can lead to serious hearing damage.
SETTING THE TIME
01) For you to be able to set the time, the equipment must be in Stand-by mode (operating display R lights up red).
02) Press MEMORY/CLK-ADJ button
\ once - the hours display flashes.
03) Move the hours setting forward or backward using the Forward button ) or Reverse button 8.
04) Press MEMORY/CLK-ADJ button \ again - the minutes display flashes.
05) Move the minutes setting forward or backward using the Forward button ) or Reverse button 8.
06) Press the MEMORY/CLK-ADJ button
\ again - the display stops flashing and the clock starts (the colon flashes).
SETTING TIMES FOR SWITCHING ON AND OFF [ » TIMER « ]
If the Switch-on time feature is enabled then your Designer Audio Unit can wake you at your chosen time.
01) Using the appropriate button
* select the desired device/ source (CD, TAPE or TUNER).
02) Set up the source, i.e. for TUNER (RADIO) set the desired station, for TAPE (CASSETTE RECORDER) insert the tape and wind
to the correct place or insert a CD and if required program a track sequence.
03) Press TIMER button
0. The display @ now shows TIMER.
NOTE: You have five seconds to complete the following steps. Otherwise the process is halted and you must begin
again with step 4.
04) Press the MODE/REMAIN button
9 twice. The time appears in display @ and TIMER ON flashes.
05) Press the MEMORY/CLK-ADJ button \ once - the hours display flashes.
06) Move the hours setting forward or backward using the Forward button ) or Reverse button 8.
07) Press MEMORY/CLK-ADJ button \ again - the minutes display flashes.
08) Move the minutes setting forward or backward using the Forward button ) or Reverse button 8.
09) Press the MEMORY/CLK-ADJ button
\ again - the Switch on time is stored.
10) If you wish to be woken to a cassette: Press the Play button 3.
11) Then switch off the Designer Audio Unit (ON-/OFF-button E).
If you enable the Switch-off time feature, your Designer Audio Unit will always switch off at the set time.
01) Press the TIMER button
0. The display @ now shows TIMER.
NOTE: You have five seconds to complete the following steps. Otherwise the process is halted and you must
begin again with step 2.
02) Press the MODE/REMAIN button
9 three times. The time appears in the display @ and TIMER OFF flashes.
03) Press the MEMORY/CLK-ADJ button \ once - the hours display flashes.
04) Move the hours setting forward or backward using the
Forward button ) or Reverse button 8.
05) Press MEMORY/CLK-ADJ button \ again - the minutes display flashes.
06) Move the minutes setting forward or backward using the Forward button ) or Reverse button 8.
07) Press the MEMORY/CLK-ADJ button
\ again - the Switch-off time is stored.
To switch off the TIMER functions, press the TIMER button 0 repeatedly until the display @ shows TIMER.
12