Filter
Top Products
ACCESSORIES
All accessories are available at www.klipsch.com.
WB-1 Wall Mount Brackets (While supplies last)
Versatile Wall Bracket 1 is made from high quality steel. The clean, simple
design affords the most extreme angle adjustment, with up to 160 degrees of
movement for precise speaker positioning in the horizontal plane. Wall stud
wood screws included.
TROUBLESHOOTING
If no sound, ensure that:
- DIN plug from Control Pod, AUX input (if desired), speaker cables, and AC
power cord are securely attached.
- Soundcard software is properly installed and functioning correctly. (Software
is provided by the sound card manufacturer.)
- The computer sound volume is turned up and not muted. Also ensure that the
control pod volume is not turned to the minimum setting.
- USB transmitter is securely connected to the computer’s USB port, and
the LED on the USB transmitter is on (not blinking). It may be necessary to
close and restart the music player software. If you suspect a problem with
the USB wireless device, perform the checks as described below in the
section “WIRELESS TROUBLESHOOTING”.
- The LED on the Control Pod is on indicating the system has power. If the LED
is not on check the DIN plug and AC power cord connection. Also check that
the AC wall outlet or power strip has power.
- Headphones are not connected.
If one or more speakers have little or no sound, ensure that:
- All cables are connected properly
- Connectors are fully “seated” in soundcard and subwoofer.
- Main and subwoofer level controls are properly adjusted on control pod
- Computer software audio settings are adjusted for proper use
- Computer system’s sound (control panel) volume is turned up
If the satellites or subwoofer exhibit distortion or buzzing:
- Turn down computer’s volume (via control panel), and reduce control pod volume
- Turn down subwoofer’s volume, as program signal may be too strong
- Plug the subwoofer’s power cord into a surge protector
If there is noise or hissing and the volume is low even when the main volume is up:
- Turn up computer’s sound volume (via control panel)
- Turn down main volume on control pod to compensate
- Ensure that software/hardware is properly installed and operating
If there is computer monitor interference:
- Make sure the sub is positioned at least 3 feet (1m) from the computer monitor
- Increase the distance between the satellite speakers and the computer monitor
WIRELESS TROUBLESHOOTING
1) Make sure sound is not muted on computer.
2) Make sure volume level setting on computer & control pod is correct.
3) Make sure green LED on USB transmitter and Red LED on subwoofer
are not blinking. If they are press each sync button.
4) Restart your music player software.
5) Make sure "Klipsch ProMedia 2.1 Wireless" is selected as the audio playback
device. If not select it, hit apply/save and restart your music player software.
6) If the above does not fix the problem leave the transmitter plugged in, restart
your computer and go to #1 above.
For more detailed information and FAQs, please visit www.klipsch.com.
FCC EMC COMPLIANCE INFORMATION:
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not in-stalled and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Approved under the verification provision of FCC Part 15 as a Class B
Digital Device.
Caution: Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate this device.
WIRELESS TRANSMITTER COMPLIANCE INFORMATION:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that permitted for successful communication.
PRODUCT REGISTRATION
Register your product online at www.klipsch.com/register
• Klipsch will keep you up-to-date on new products and promotions
• Your personal information will never be resold
• This registration information is not used for warranty purposes.
Please retain your receipt for warranty claims.