Filter
Top Products
English- 9
Connecting Wires to Terminals
8 -English
+-
TERR
SAT
ANT
FUSE 3A
BATT
GND
TO HEAD UNIT
TO CHANGER
TERR
SAT
ANT
FUSE 3A
BATT
GND
Control unit
Sirius
Satellite
Radio tuner
Disc changer
To KENWOOD disc changer / DAB
control input / Sirius control input
Sirius connection wire
(Accessory1)
To control unit
Fuse (3A)
KENWOOD disc changer
control input
Sirius antenna
wire
Sirius antenna
(Separated-sale
product)
Ground wire
(Commercially available)
Battery wire
(Commercially available)
Battery
To connect the Disc changer,
consult your Disc changer
manual.
NOTE
Connection wire
(supplied with the
Disc changer)
(Front side)
(Rear side)
The use of any accessories except for those provided might result in damage to the unit. Make
sure only to use the accessories shipped with the unit, as shown above.
2CAUTION
Accessories
1
2
3
4
5
7
6
Installation Procedure
1. To prevent short circuits, remove the key
from the ignition and disconnect the -
terminal of the battery.
2. Install the Sirius antenna and connect the
antenna wire to the Sirius satellite radio
tuner.
3. Connect the Sirius satellite radio tuner and
the control unit using the provided Sirius
connection wire.
4. Make the proper input and output wire
connections for each unit.
5. Connect the battery wire and ground wire to
the Sirius satellite radio tuner.
6. Install the unit in your car.
7. Reconnect the - terminal of the battery.
8. Press the reset button on the control unit.
• Do not connect the Sirius control wire
while the control unit is turned ON.
• Be sure to press the reset button on the
control unit after installation.
• If your car is not prepared for this special
connection-system, consult your
Kenwood dealer.
• Make sure that all wire connections are
securely made by inserting jacks until
they lock completely.
2CAUTION
• Some disc changers need conversion
wires for connection. See the section on
"Safety Precautions" for details.
• Do not let unconnected wires or
terminals touch metal on the car or
anything else conducting electricity. To
prevent short circuits, also do not
remove the caps on the ends of the
unconnected wires or the terminals.
• If the fuse blows, first make sure that the
wires have not caused a short circuit, then
replace the old fuse with one with the
same rating.
• Insulate unconnected wires with vinyl
tape or other similar material.
• Take care so that the antenna wire and
other connection wires are not caught by
mobile parts. Otherwise wire
disconnection or other trouble may
result.
• Do not apply too much force on the
antenna wire, other connection wires
and connectors by bending a wire, etc.
Otherwise wire disconnection or other
trouble may result.
• After the unit is installed, check whether
the brake lamps, indicators, wipers, etc.
on the car are working properly.
Power terminal
Pass battery and ground wires through
supplied terminal cover and connect to
respective terminals. After completing
connections, fasten terminal cover5 over
terminal bracket.
Terminal cover
(Accessory5)
Lead terminal
(Commercially
available)
Car fuse
box (Main
fuse)
Connect the KTC-SR901 to the
terminal labelled TO CHANGER 2.
Set the PROTOCOL selection
switch to "N" position.
NOTE
CHANGER
CHANGER 2
TO
CHANGER 1
TO
H/U
TO
SWITCH
AUX
OFF ON
SWITCH
PROTOCOL
ON
IN
AUX
]“N”
HEAD UNIT
TO
TO
Disc changer
Control unit
■ If you want to connect KCA-S210A
KCA-S210A
Sirius Satellite Radio tuner
Terminal cover
(Accessory5)