Filter
Top Products
22
EN
# Press the
∧
key or # key again to accept the setting.
• The subwoofer remix setting indication “SW RE-MIX” appears.
$ Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate subwoofer re-mix setting.
1 SW RE-MIX ON : Subwoofer re-mix setting mode to
the receiver is ON.
2 SW RE-MIX OFF : Subwoofer re-mix setting mode to
the receiver is OFF.
• If subwoofer is turned off, subwoofer re-mix setting is not visible.
% Press the SETUP key again to return to the main setup
displays.
• The receiver enters the speaker volume level adjustment mode.
• In steps 4 and 5, indications appear only for the selected
channels of the speakers that require adjusting.
5
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. Using a
handheld SPL meter at arms length from your body, adjust the noise
to read 75dB when set to “C” weighting, “Slow” reading on the
meter. If you do not have an SPL meter, adjust the volume levels so
that the speakers sound about the same level, starting at the 0dB
setting on the display.
1 Press the
∧
/
∨
keys or @/#keys to select TEST TONE.
2 Press the SETUP key for the following displays:
1 T.TONE AUTO
2 T.TONE MANUAL
3 The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or Multi (%/fi) keys.
Press the SETUP key again to begin TEST TONE.
Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust
the volume level of the test tone output from the speaker
channel to be adjusted.
For AUTO selection, the first test tone is heard from the front left
speaker for 2.5 seconds. The next test tone is heard from the
speakers in the following sequence for 2 seconds each.
When the 6ch AMP SB has been selected.
LEFT CNTR RIGHT SR
SBSLSUBW
When the 6ch AMP SW or OFF has been selected.
LEFT CNTR RIGHT SR
SBL SBRSLSUBW
The channel indication blinks while the test tone is being output.
L
SL S SB SR
CR
SP MUTE
OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed. fi
• If the speaker setting selects are OFF, the speaker level settings
are reset.
For MANUAL selection, press the
∧
/
∨
keys or @/# keys each
time to select the speaker channel.
4 Press the SETUP key again.
• The test tone is turned off and return to the main setup displays.
Preparing for surround sound
7 Press the
∧
key or # key again to accept the setting.
• The surround speaker setting indication “SURR” appears.
8 Use the MULTI CONTROL knob or Multi (%/fi) to select the
appropriate surround speaker setting.
If you selected “LARGE” as the center speaker setting,
1 SURR LARGE : Large surround speakers are
connected to the receiver.
2 SURR NML/THX : Average size surround speakers are
connected to the receiver.
3 SURR OFF : Surround speaker setting mode to
the receiver is OFF.
If you selected other than “LARGE” as the center speaker setting,
1 SURR NML/THX : Surround speaker setting mode
to the receiver is ON.
2 SURR OFF : Surround speaker setting mode to
the receiver is OFF.
• When the setting “SURR OFF” is selected, the procedure skips
to step #.
9 Press the
∧
key or # keys again to accept the setting.
• The surround speaker setting indication “SB” appears.
0 Use the MULTI CONTROL knob or Multi (%/fi) keys to
select appropriate surround back speaker setting.
If you selected “LARGE” as the surround speaker setting,
1 SB NML/THX : Average size surround back speaker is
connected to the receiver.
2 SB LARGE : Large surround back speaker is
connected to the receiver.
3 SB OFF : Surround back speaker setting mode to
the receiver is OFF.
L
SL S SB SR
CR
SP MUTE
OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
If you selected “NORMAL” as the surround speaker setting,
1 SB ON : Surround back speaker setting mode to the
receiver is ON.
2 SB OFF : Surround back speaker setting mode to the
receiver is OFF.
• After setting SB (surround back) from OFF to ON, 6ch AMP setup
display will appear to enable you to re-select either SW or SB from
the surround back or subwoofer speaker terminal.
! Press the
∧
key or # key again to accept the setting and
“SURR:MIX” appears.
• Surr:mix is when the SL and SR speakers signals are mixed to
produce sound from the surround back speaker which would
enable the listener to enjoy sound coming from the back.
L
SL S SB SR
CR
SP MUTE
OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
@ Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the following.
1 SURR:MIX ON : Surround mix setting mode to the
receiver is ON.
2 SURR:MIX OFF : Surround mix setting mode to the
receiver is OFF.
• If surround back speaker is turned off, SURR:MIX setting is not
visible and the procedure skips to step #.