Kenwood VR-506 Stereo System User Manual


 
42
Additional Information
Notes
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
Specifications
Caution : Read this page carefully to ensure safe
operation.
AUDIO section (KRF-V5550D)
Effective power output during SURROUND operation
(1kHz, 10%, 8) ........................................................... 110 W + 110 W
Rated power output during STEREO operation
80 watts per channel minimum RMS, both channels driven, at
8 from 40 Hz to 20 kHz with no more than 0.7% total
harmonic distortion. (FTC)
Effective power output during SURROUND operation
FRONT (1kHz, 10% T.H.D. at 8 one channel driven)
.............................................................................. 130 W + 130 W
CENTER (1kHz, 10% T.H.D. at 8 one channel driven)
............................................................................................. 130 W
SURROUND (1kHz, 10% T.H.D. at 8 one channel driven)
.............................................................................. 130 W + 130 W
Total harmonic distortion.........................0.050% (1 kHz, 40W, 8 )
Frequency response
CD ............................................. 10 Hz ~ 60 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
CD, TUNER, AUX, TAPE .....................................................90 dB
Input sensitivity / impedance
CD ......................................................................... 200 mV / 47 k
MONITOR IN (VIDEO2/MONITOR) .....................200 mV / 47 k
Output level / impedance
TAPE REC ..............................................................200 mV / 1 k
MONITOR OUT (VIDEO2/MONITOR) ...................200 mV / 1 k
Tone control
BASS ................................................................ ±10 dB (at 70 Hz)
TREBLE .......................................................... ±10 dB (at 10 kHz)
DIGITAL AUDIO section
Sampling frequency ......................32 kHz, 44.1 kHz, 48 kHz, 96kHz
Input level / impedance / wave length
Optical ........................... (–15 dBm ~ –21 dBm), 660 nm ±30nm
Coaxial ................................................................. 0.5 Vp-p / 75
VIDEO section
VIDEO inputs / outputs
VIDEO (composite) ................................................1 Vp-p / 75
S VIDEO inputs / outputs (KRF-V6050D)
S VIDEO (luminance signal) .................................1 Vp-p / 75
S VIDEO (chrominance signal)...................... 0.286 Vp-p / 75
FM tuner section
Tuning frequency range ................................... 87.5 MHz ~ 108 MHz
Usable sensitivity (MONO)
................ 1.6 µV (75 )/ 15.2 dBf (75 kHz DEV., SINAD 30 dB)
50dB quieting sensitivity
STEREO ................................................... 28 µV (75 )/ 40.2 dBf
Total harmonic distortion (1 kHz)
MONO ........................................................ 0.5% (71.2 dBf input)
STEREO .................................................... 0.7% (71.2 dBf input)
Signal to noise ratio (1 kHz, 75 kHz DEV.)
MONO ....................................................... 75 dB (71.2 dBf input)
STEREO ................................................... 68 dB (71.2 dBf input)
Stereo separation (1 kHz) ..........................................................40 dB
Selectivity (±400 kHz).................................................................50 dB
Frequency response ................. (30 Hz ~ 15kHz), +0.5 dB, –3.0 dB
AM tuner section
Tuning frequency range
9 kHz step ................................................... 531 kHz ~ 1,602 kHz
10 kHz step ................................................. 530 kHz ~ 1,610 kHz
Usable sensitivity ................................................. 16 µV / (600 µV/m)
Signal to noise ratio (30% mod. 1 mV input)...........................50 dB
For other countries
AUDIO section (KRF-V6050D)
Effective power output during STEREO operation
1kHz,10% T.H.D.,at 8 Ω ........................................... 140 W + 140 W
Rated power output during STEREO operation
100 watts per channel minimum RMS, both channels driven, at
8 from 40 Hz to 20 kHz with no more than 0.7% total harmonic
distortion.(FTC)
Effective power output during SURROUND operation
FRONT (1kHz, 10% T.H.D. at 8 one channel driven)
.............................................................................. 140 W + 140 W
CENTER (1kHz, 10% T.H.D. at 8 one channel driven)
............................................................................................. 140 W
SURROUND (1kHz, 10% T.H.D. at 8 one channel driven)
.............................................................................. 140 W + 140 W
Total harmonic distortion .........................0.050% (1 kHz, 50W, 8 )
Frequency response
CD ............................................. 10 Hz ~ 60 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
PHONO (MM)........................................................................74 dB
CD .........................................................................................90 dB
Input sensitivity / impedance
PHONO (MM).........................................................2.5 mV / 27 k
CD ......................................................................... 200 mV / 47 k
VIDEO2/MONITOR............................................... 200 mV / 47 k
DVD/6ch INPUT ...................................................200 mV / 47 k
Output level / impedance
TAPE REC ..............................................................200 mV / 1 k
VIDEO2/MONITOR .................................................200 mV / 1 k
PRE OUT (SUBWOOFER)...................................... 1.5 V / 2.2 k
Tone control
BASS ................................................................ ±10 dB (at 70 Hz)
TREBLE.......................................................... ±10 dB (at 10 kHz)
AUDIO section (KRF-V5050D)
Effective power output during STEREO operation
(1 kHz, 10%, 8) .......................................................... 140 W + 140 W
Rated power output during STEREO operation
100 watts channel minimum RMS, both channels driven, at 8
from 40 Hz to 20 kHz with no more than 0.7% total harmonic
distortion. (FTC)
Effective power output during SURROUND operation
FRONT (1kHz, 10% T.H.D. at 8 one channel driven)
.............................................................................. 140 W + 140 W
CENTER (1kHz, 10% T.H.D. at 8 one channel driven)
............................................................................................. 140 W
SURROUND (1kHz, 10% T.H.D. at 8 one channel driven)
.............................................................................. 140 W + 140 W
Total harmonic distortion .........................0.050% (1 kHz, 50W, 8 )
Frequency response
CD ............................................. 10 Hz ~ 60 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
PHONO (MM)........................................................................74 dB
CD, TUNER, AUX, TAPE .....................................................90 dB
Input sensitivity / impedance
PHONO (MM).........................................................2.5 mV / 27 k
CD ......................................................................... 200 mV / 47 k
MONITOR IN (VIDEO2/MONITOR) .....................200 mV / 47 k
DVD/6ch INPUT ...................................................200 mV / 10 k
Output level / impedance
TAPE REC ..............................................................200 mV / 1 k
MONITOR OUT (VIDEO2/MONITOR) ...................200 mV / 1 k
PRE OUT (SUBWOOFER)...................................... 1.5 V / 2.2 k
Tone control
BASS ................................................................ ±10 dB (at 70 Hz)
TREBLE.......................................................... ±10 dB (at 10 kHz)
_4942/32-44/EN 3/16/01, 3:11 PM42