Kenwood KDC-MP338 CD Player User Manual


 
Accessories/Installation Procedure
Accessories
Installation Procedure
1.
To
prevent a short circuit, remove the key from the
ignition and disconnect the
8 battery.
2.
Make the proper
input
and
output
wire
connections for each unit.
3.
Connect the speaker wires
of
the wiring harness.
4.
Connect the wiring harness wires in the following
order: ground, battery, ignition.
5.
Connect the wiring harness connector
to
the unit.
6.
Install the unit
in
your
car.
7.
Reconnect the 8 battery.
8.
Press
the reset button.
AWARNING
If
you connect the ignition wire (red) and the battery wire
(yellow)
to
the
car
chassis
(ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires
to
the power source running through the fuse box.
&
Mounting and wiring this product requires skills and
experience.
For
safety's
sake,
leave the
mounting
and wiring
work
to
professionals.
Make sure
to
ground the unit
to
a negative
12V
DC
power
supply.
Do
not
install the unit in a spot exposed
to
direct sunlight
or excessive heat
or
humidity. Also avoid places
with
too
much dust or the possibility
of
water splashing.
Do
not
use
your
own
screws.
Use
only the screws provided.
If
you
use
the wrong screws, you could damage the unit.
If
the power
is
not
turned
ON
("PROTECT"
is
displayed),
the speaker wire may have a short-circuit or touched the
chassis
of
the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
If
your
car's
ignition does
not
have
an
ACC
position, connect
the ignition wires
to
a power source that can
be
turned
on
and
off
with
the ignition
key.
If you connect the ignition
wire
to
a power source
with
a constant voltage supply,
as
with
battery wires, the battery may die.
If the console
has
a lid, make
sure
to
install the unit
so
that
the faceplate will
not
hit the lid when closing and opening.
If the fuse blows, first make
sure
the wires aren't touching
to
cause a short circuit, then replace the old fuse
with
one
with
the same rating.
Insulate unconnected wires
with
vinyl tape
or
other similar
material.
To
prevent a short circuit,
do
not
remove the caps
on the ends
of
the unconnected wires
or
the terminals.
Connect the speaker wires correctly
to
the terminals
to
which they correspond. The unit may be damaged or fail
to
work
if
you share
the
8 wires
or
ground
them
to
any metal
part in the
car.
When only
two
speakers
are
being connected
to
the
system, connect the connectors either
to
both
the front
output
terminals
or
to
both
the
rear
output
terminals (do
not
mix front and
rear).
For
example,
if
you connect the
<±)
connector
of
the left speaker
to
a front
output
terminal,
do
not
connect the 8 connector
to
a rear
output
terminal.
After the unit
is
installed, check whether the brake lamps,
blinkers, wipers, etc. on the
car
are
working properly.
Mount
the unit
so
that the
mounting
angle
is
30·
or
less.
About
CD
players/disc changers connected
to
this
unit
Kenwood disc changers/
CD
players released in 1998
or later
can
be connected
to
this unit.
Refer
to
the catalog or consult your Kenwood dealer
for connectable models
of
disc changers/
CD
players.
Note that any Kenwood disc changers/
CD
players
released in
1997
or earlier and disc changers made by
other makers cannot be connected
to
this unit.
Connecting unsupported disc changers/CD players
to
this unit may result in damage.
Set
the "O-N" Switch to the
"N"
position for the
applicable Kenwood disc changers/
CD
players.
The functions you
can
use
and the information that
can
be displayed may differ depending on the models
being connected.
18 I KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338